McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    273 Products

    Peel-Away Multilayer Shim Stock

    Image of ProductInUse. Front orientation. Shim Stock. Peel Away, Sold Individually, Multilayer.
    Fine-tune thickness without worrying about stacking multiple shims. Cut the shim stock into custom shapes that suit your needs. It's made of layers of material bonded with adhesive—peel off the layers with a utility knife until you reach your desired thickness. To make peeling easier, warm the created shims to soften the adhesive. With thickness tolerances as fine as a strand of hair, the shims will precisely align, space, and level components on dies, presses, and machinery.
    18-8 Stainless Steel—The choice for wet and outdoor areas because it resists rust. However, it will corrode or pit when exposed to salt water and chemicals.
    Carbon Steel—Best for dry areas since moisture will cause it to rust.
    Aluminum—An alternative to stainless steel for rust resistance but less hard so it may not retain its shape. One-third the weight of steel, it's often used in robotics and automation.
    Brass—Picked for its warm, polished look. Similar to 18-8 stainless steel, it resists rusting in wet and outdoor areas.
    Polyimide—Originally designed for military aircraft, it’s used in everything from aerospace to electronics where weight, electrical insulation, and precision are vital.
    Temper Rating—Choose half hard to create shims that you’ll need to bend or shape. Opt for full hard to make stronger shims that will maintain their shape under loads.
    Certificate
    Thk.
    Thk. Tolerance
    No. of
    Layers
    Layer
    Thk.
    Temper
    Rating
    Type
    Form
    Specs. Met
    Form
    Each
    18-8 Stainless Steel
     
    12" Wide × 12" Long
    0.008"-0.0005" to 0.001"40.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.01"-0.0005" to 0.0015"50.002"———SAE AMS-DTL-22499Sheet000000000000
    0.015"-0.001" to 0.0015"50.003"———SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"80.002"———SAE AMS-DTL-22499Sheet000000000000
    0.02"-0.001" to 0.002"100.002"———SAE AMS-DTL-22499Sheet000000000000
    0.021"-0.001" to 0.002"70.003"———SAE AMS-DTL-22499Sheet000000000000
    0.032"-0.002" to 0.003"160.002"———SAE AMS-DTL-22499Sheet000000000000
    0.033"-0.002" to 0.003"110.003"———SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"160.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.048"-0.002" to 0.005"240.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.062"-0.002" to 0.006"310.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.063"-0.002" to 0.006"210.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.093"-0.003" to 0.009"310.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.094"-0.003" to 0.009"470.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.124"-0.003" to 0.012"620.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.126"-0.003" to 0.012"420.003"———SAE AMS-DTL-22499Sheet0000000000000
     
    20" Wide × 24" Long
    0.008"-0.0005" to 0.001"40.002"———SAE AMS-DTL-22499Sheet000000000000
    0.01"-0.0005" to 0.0015"50.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.015"-0.001" to 0.0015"50.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.016"-0.001" to 0.0015"80.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.02"-0.001" to 0.002"100.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.021"-0.001" to 0.002"70.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.032"-0.002" to 0.003"160.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.033"-0.002" to 0.003"110.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.048"-0.002" to 0.005"160.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.048"-0.002" to 0.005"240.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.062"-0.002" to 0.006"310.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.063"-0.002" to 0.006"210.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.093"-0.003" to 0.009"310.003"———SAE AMS-DTL-22499Sheet0000000000000
    0.094"-0.003" to 0.009"470.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.124"-0.003" to 0.012"620.002"———SAE AMS-DTL-22499Sheet0000000000000
    0.126"-0.003" to 0.012"420.003"———SAE AMS-DTL-22499Sheet0000000000000
     
    Carbon Steel
     
    12" Wide × 12" Long
    0.006"-0.0005" to 0.001"30.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.008"-0.0005" to 0.001"40.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.01"-0.0005" to 0.0015"50.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.015"-0.001" to 0.0015"50.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"80.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.02"-0.001" to 0.002"100.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.021"-0.001" to 0.002"70.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.032"-0.002" to 0.003"160.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.033"-0.002" to 0.003"110.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"160.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"240.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.062"-0.002" to 0.006"310.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.063"-0.002" to 0.006"210.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.093"-0.003" to 0.009"310.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.094"-0.003" to 0.009"470.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.124"-0.003" to 0.012"620.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.126"-0.003" to 0.012"420.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
     
    20" Wide × 24" Long
    0.006"-0.0005" to 0.001"30.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.008"-0.0005" to 0.001"40.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.01"-0.0005" to 0.0015"50.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.015"-0.001" to 0.0015"50.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"80.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.02"-0.001" to 0.002"100.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.021"-0.001" to 0.002"70.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.032"-0.002" to 0.003"160.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.033"-0.002" to 0.003"110.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"160.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.048"-0.002" to 0.005"240.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.062"-0.002" to 0.006"310.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.063"-0.002" to 0.006"210.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.093"-0.003" to 0.009"310.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.094"-0.003" to 0.009"470.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.124"-0.003" to 0.012"620.002"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
    0.126"-0.003" to 0.012"420.003"———Fed. Spec. QQ-S-698, SAE AMS-DTL-22499Sheet0000000000000
     
    Aluminum
     
    12" Wide × 12" Long
    0.006"-0.0005" to 0.001"30.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.008"-0.0005" to 0.001"40.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.01"-0.0005" to 0.0015"50.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"50.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"80.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.02"-0.001" to 0.002"100.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.021"-0.001" to 0.002"70.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.032"-0.002" to 0.003"160.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.033"-0.002" to 0.003"110.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"160.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"240.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.062"-0.002" to 0.006"310.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.063"-0.002" to 0.006"210.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.094"-0.003" to 0.009"310.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.094"-0.003" to 0.009"470.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.125"-0.003" to 0.012"410.003"Full Hard——SAE AMS-DTL-22499Sheet000000000000
    0.125"-0.003" to 0.012"620.002"Full Hard——SAE AMS-DTL-22499Sheet000000000000
     
    24" Wide × 24" Long
    0.187"-0.003" to 0.018"620.003"Full Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.25"-0.005" to 0.025"830.003"Full Hard——SAE AMS-DTL-22499Sheet0000000000000
     
    Brass
     
    8" Wide × 24" Long
    0.006"-0.0005" to 0.001"30.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.008"-0.0005" to 0.001"40.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.01"-0.0005" to 0.0015"50.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"80.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.02"-0.001" to 0.002"100.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.032"-0.002" to 0.003"160.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"240.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.062"-0.002" to 0.006"310.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.094"-0.003" to 0.009"470.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.124"-0.003" to 0.012"620.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
     
    12" Wide × 12" Long
    0.02"-0.001" to 0.002"100.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.032"-0.002" to 0.003"160.002"1/2 Hard——SAE AMS-DTL-22499Sheet000000000000
    0.048"-0.002" to 0.005"240.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.062"-0.002" to 0.006"310.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.094"-0.003" to 0.009"470.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
    0.124"-0.003" to 0.012"620.002"1/2 Hard——SAE AMS-DTL-22499Sheet0000000000000
     
    Polyimide
     
    12" Wide × 12" Long
    0.008"-0.0005" to 0.001"20.004"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.01"-0.001" to 0.0015"50.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet000000000000
    0.016"-0.001" to 0.0015"80.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.02"-0.001" to 0.002"100.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.032"-0.002" to 0.003"160.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.048"-0.002" to 0.005"230.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.062"-0.002" to 0.006"300.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.094"-0.003" to 0.009"460.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
    0.124"-0.003" to 0.012"610.002"—Material Certificate
    		Paper
    		ASTM D5213, SAE AMS-DTL-22499Sheet0000000000000
     

    Peel-Away Multilayer Shims

    Image of Product. Front orientation. Shims. Sold Individually, Peel Away, Multilayer, Round.
    Fine-tune thickness without worrying about stacking multiple shims. These shims are made of metal layers bonded with adhesive—peel off the layers with a utility knife until you reach your desired thickness. To make peeling easier, warm the shims to soften the adhesive. With thickness tolerances as fine as a strand of hair, all of these shims precisely align, space, and level components on shafts, arbors, and machinery.
    18-8 Stainless Steel—The choice for wet and outdoor environments, these shims resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.
    Aluminum—These shims are an alternative to stainless steel for rust resistance but aren't as hard so they may not retain their shape as well. One-third the weight of steel, they’re commonly used in robotics and automation.
    Brass—With a warm, polished look, these shims are often chosen for their appearance. Similar to 18-8 stainless steel, brass is corrosion resistant enough to stand up to wet environments.
    Material Certificate—Shims include a report with a traceable lot number.
    Thk.
    Thk. Tolerance
    ID Tolerance
    OD Tolerance
    No. of
    Layers
    Layer
    Thk.
    Min.
    Hardness
    Certificate Type
    Specs. Met
    Mil.
    Spec.
    Each
    18-8 Stainless Steel
     
    3/8" ID × 5/8" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Rockwell B75—ASTM A666—000000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Rockwell B75—ASTM A666—00000000000000
     
    1/2" ID × 3/4" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Rockwell B75—ASTM A666—00000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Rockwell B75—ASTM A666—00000000000000
     
    5/8" ID × 1" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Rockwell B75—ASTM A666—00000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Rockwell B75—ASTM A666—00000000000000
    0.125"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"620.002"Rockwell B75—ASTM A666—00000000000000
     
    3/4" ID × 1 1/8" OD
    0.125"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"620.002"Rockwell B75—ASTM A666—00000000000000
     
    7/8" ID × 1 3/8" OD
    0.125"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"620.002"Rockwell B75—ASTM A666—00000000000000
     
    Aluminum
     
    3/8" ID × 5/8" OD
    0.032"-0.002" to 0.003"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated———0000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated———0000000000000
     
    1/2" ID × 3/4" OD
    0.032"-0.002" to 0.003"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated———0000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated———00000000000000
     
    5/8" ID × 1" OD
    0.032"-0.002" to 0.003"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated———00000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated———00000000000000
     
    1" ID × 1 1/2" OD
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated———00000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated———00000000000000
     
    1 1/2" ID × 2 1/8" OD
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated———00000000000000
     
    Brass
     
    0.135" ID × 0.234" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated———0000000000000
     
    0.193" ID × 3/8" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated———0000000000000
     
    0.255" ID × 1/2" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not RatedMaterial Certificate
    		——0000000000000
     
    3/8" ID × 5/8" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    1/2" ID × 3/4" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    5/8" ID × 1" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    3/4" ID × 1 1/8" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    7/8" ID × 1 3/8" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    1" ID × 1 1/2" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    1 1/4" ID × 1 3/4" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     
    1 1/2" ID × 2 1/8" OD
    0.032"-0.005" to 0.005"-0.01" to 0.01"-0.01" to 0.01"160.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.062"-0.002" to 0.006"-0.01" to 0.01"-0.01" to 0.01"310.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
    0.125"-0.003" to 0.012"-0.01" to 0.01"-0.01" to 0.01"620.002"Not Rated—ASTM B36, SAE AMS-DTL-22499MIL-S-569700000000000000
     

    Peel-Away Multilayer Made-to-Order Shims

    Image of Product. Front orientation. Shims. Multilayer, Sold Individually, Made-to-Order, Peel Away.
    If you need a unique peel-away shim shape or size, we’ll precision cut it for you. Use these shims to fine-tune thickness without worrying about stacking multiple shims. They're made of metal layers bonded with adhesive—peel off the layers with a utility knife until you reach your desired thickness. To make peeling easier, warm the shims to soften the adhesive. With thickness tolerances as fine as a strand of hair, all of these shims precisely align, space, and level components on shafts, arbors, and machinery.
    Send your dimensioned DWG, DXF, IGES, or STEP file to sales@mcmaster.com. Please leave at least 1/8" wall between shim edge and holes. Minimum hole size is 1/4". Shims should be no smaller than 1" × 1" square or 1" OD. Maximum shim dimension is the largest overall length, width, or diameter of your custom shim.
    18-8 Stainless Steel—The choice for wet and outdoor environments, these shims resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.
    Carbon Steel—Best for dry environments since moisture will cause these shims to rust.
    Aluminum—These shims are an alternative to stainless steel for rust resistance but aren't as hard so they may not retain their shape as well. One-third the weight of steel, they’re commonly used in robotics and automation.
    Brass—With a warm, polished look, these shims are often chosen for their appearance. Similar to 18-8 stainless steel, brass is corrosion resistant enough to stand up to wet environments.
    Material Certificate—Shims include a report with a traceable lot number.
    2" × 2" Maximum
    Shim Size
    5" × 5" Maximum
    Shim Size
    7" × 7" Maximum
    Shim Size
    11" × 11" Maximum
    Shim Size
    23" × 23" Maximum
    Shim Size
    Thk.
    Thk. Tolerance
    No. of
    Layers
    Layer
    Thk.
    Min.
    Hardness
    Certificate Type
    Specs. Met
    Pkg.
    Qty.
    Pkg.
    Pkg.
    Qty.
    Pkg.
    Pkg.
    Qty.
    Pkg.
    Pkg.
    Qty.
    Pkg.
    Pkg.
    Qty.
    Pkg.
    18-8 Stainless Steel
    0.008"-0.0004" to 0.0004"40.002"Rockwell B80Material Certificate
    		ASTM A24016000000000000000040000000000000000900000000000000004000000000000000010000000000000000
    0.016"-0.0008" to 0.0008"80.002"Rockwell B80Material Certificate
    		ASTM A240160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.032"-0.0016" to 0.0016"160.002"Rockwell B80Material Certificate
    		ASTM A240160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.048"-0.0024" to 0.0024"240.002"Rockwell B80Material Certificate
    		ASTM A240160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.062"-0.0031" to 0.0031"320.002"Rockwell B80Material Certificate
    		ASTM A240160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.124"-0.0062" to 0.0062"620.002"Rockwell B80Material Certificate
    		ASTM A240160000000000000004000000000000000900000000000000000400000000000000000100000000000000000
     
    Carbon Steel
    0.008"-0.0004" to 0.0004"40.002"Rockwell B54Material Certificate
    		Fed. Spec. QQ-S-6981600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.016"-0.0008" to 0.0008"80.002"Rockwell B54Material Certificate
    		Fed. Spec. QQ-S-6981600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.032"-0.0016" to 0.0016"160.002"Rockwell B54Material Certificate
    		Fed. Spec. QQ-S-698160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.048"-0.0024" to 0.0024"240.002"Rockwell B54Material Certificate
    		Fed. Spec. QQ-S-698160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.062"-0.0031" to 0.0031"320.002"Rockwell B54Material Certificate
    		Fed. Spec. QQ-S-698160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.124"-0.0062" to 0.0062"620.002"Rockwell B54Material Certificate
    		Fed. Spec. QQ-S-698160000000000000004000000000000000900000000000000040000000000000001000000000000000
     
    Aluminum
    0.008"-0.0004" to 0.0004"40.002"Not RatedMaterial Certificate
    		ASTM B209, SAE AMS-DTL-224991600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.016"-0.0008" to 0.0008"80.002"Not RatedMaterial Certificate
    		ASTM B209, SAE AMS-DTL-224991600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.032"-0.0016" to 0.0016"160.002"Not RatedMaterial Certificate
    		ASTM B209, SAE AMS-DTL-224991600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.048"-0.0024" to 0.0024"240.002"Not RatedMaterial Certificate
    		ASTM B209, SAE AMS-DTL-224991600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.062"-0.0031" to 0.0031"320.002"Not RatedMaterial Certificate
    		ASTM B209, SAE AMS-DTL-224991600000000000000400000000000000900000000000000040000000000000001000000000000000
    0.124"-0.0062" to 0.0062"620.002"Not RatedMaterial Certificate
    		ASTM B209, SAE AMS-DTL-22499160000000000000004000000000000000900000000000000040000000000000001000000000000000
     
    Brass
    0.008"-0.0004" to 0.0004"40.002"Not RatedMaterial Certificate
    		ASTM B36160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.016"-0.0008" to 0.0008"80.002"Not RatedMaterial Certificate
    		ASTM B36160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.032"-0.0016" to 0.0016"160.002"Not RatedMaterial Certificate
    		ASTM B36160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.048"-0.0024" to 0.0024"240.002"Not RatedMaterial Certificate
    		ASTM B36160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.062"-0.0031" to 0.0031"320.002"Not RatedMaterial Certificate
    		ASTM B36160000000000000004000000000000000900000000000000040000000000000001000000000000000
    0.124"-0.0062" to 0.0062"620.002"Not RatedMaterial Certificate
    		ASTM B36160000000000000004000000000000000900000000000000000400000000000000000100000000000000000
     
    back to top