System of Measurement System of Measurement |
|---|
|
Diameter Diameter | Show |
|---|
|
Diameter Diameter | Hide |
|---|
Material Material |
|---|
|
Shaft Type Shaft Type |
|---|
 | Plain |
Specifications Met Specifications Met |
|---|
End Type End Type |
|---|
 | Plain |
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Tolerance Rating Tolerance Rating |
|---|
|
Minimum Hardness Minimum Hardness |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
Passivation Passivation |
|---|
|
Breaking Strength Breaking Strength |
|---|
|
Head Diameter Head Diameter |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Head Height Head Height |
|---|
|
Dowel Pins
Use dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts. For a tight fit, your hole should be equal to or slightly smaller than the diameter shown. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces.
Stainless steel pins are more corrosion resistant than steel pins. Pins that are passivated offer added protection against corrosion and oxidation. Stainless steel pins are precision ground except for 1/64" diameter pins. 18-8 stainless steel pins offer a balance of strength and corrosion resistance. They may be mildly magnetic. 316 stainless steel pins have the best corrosion resistance of our stainless steel pins. They may be mildly magnetic. Some pins meet material and dimensional standards set by ASME, Mil. Spec., DIN, or ISO. ISO 2338-m6 is functionally equivalent to DIN 7, but the ends are chamfered instead of rounded.
For technical drawings and 3-D models, click on a part number.
| Lg., mm | Dia. Tolerance, mm | Min. Hardness | Breaking Strength | Passivation | Specifications Met | Pkg. Qty. | Pkg. | |
0.8 mm Dia. | ||||||||
|---|---|---|---|---|---|---|---|---|
| 3 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 000000 |
| 4 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 5 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 6 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 8 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 10 | 0 to 0.008 | Not Rated | Not Rated | __ | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 12 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 14 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 16 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 18 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 00000 |
| 20 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| Lg., mm | Dia. Tolerance, mm | Min. Hardness | Breaking Strength | Passivation | Specifications Met | Pkg. Qty. | Pkg. | |
0.8 mm Dia. | ||||||||
|---|---|---|---|---|---|---|---|---|
| 4 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 10 | 000000000 | 000000 |
| 5 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 6 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 8 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 10 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 12 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 14 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 16 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 18 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
| 20 | 0.002 to 0.008 | Not Rated | Not Rated | Passivated | ISO 2338-m6 | 5 | 000000000 | 0000 |
Core Pins
Mold plastic around these pins to form small holes, or use them to perforate parts. They have a flat head to fit into a counterbored hole. Pins can be machined to fit your application. They're precision-ground to tight tolerances. Made of M2 tool steel, these pins are wear resistant and stay sharp at high temperatures.
For technical drawings and 3-D models, click on a part number.
Head | ||||||
|---|---|---|---|---|---|---|
| Dia. | Dia. Tolerance | Dia. | Ht. | Min. Hardness | Each | |
M2 Tool Steel | ||||||
63mm Lg. | ||||||
| 0.800mm | 0mm to 0.008mm | 3mm | 5mm | Rockwell C60 | 000000000 | 000000 |