System of Measurement System of Measurement |
|---|
|
Diameter Diameter | Show |
|---|
|
Diameter Diameter | Hide |
|---|
Material Material |
|---|
|
Pin Type Pin Type |
|---|
 | Dowel |
Head Type Head Type |
|---|
 | Plain |
End Type End Type |
|---|
 | Plain |
Shaft Type Shaft Type |
|---|
| Plain |
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
Tolerance Rating Tolerance Rating |
|---|
|
Breaking Strength Breaking Strength |
|---|
|
Minimum Hardness Minimum Hardness |
|---|
|
Body Shape Body Shape |
|---|
|
Body Texture Body Texture |
|---|
|
Individual/Set Individual/Set |
|---|
|
Thread Size Thread Size |
|---|
Dowel Pins
Use dowel pins as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts. For a tight fit, your hole should be equal to or slightly smaller than the diameter shown. Breaking strength is measured as double shear, which is the force required to break a pin into three pieces.
Steel pins are the strongest dowel pins. Steel pins are precision ground except for 1/32" diameter pins.
For technical drawings and 3-D models, click on a part number.
| Lg. | Dia. Tolerance | Min. Hardness | Breaking Strength, lbs. | Pkg. Qty. | Pkg. | |
11/16" Dia. | ||||||
|---|---|---|---|---|---|---|
| 3/4" | 0.0001" to 0.0003" | Rockwell C50 | Not Rated | 1 | 000000000 | 00000 |
| 1" | 0.0001" to 0.0003" | Rockwell C50 | Not Rated | 1 | 000000000 | 0000 |
| 1 1/2" | 0.0001" to 0.0003" | Rockwell C50 | Not Rated | 1 | 000000000 | 00000 |
| 2" | 0.0001" to 0.0003" | Rockwell C50 | Not Rated | 1 | 000000000 | 00000 |
| 2 1/2" | 0.0001" to 0.0003" | Rockwell C50 | Not Rated | 1 | 000000000 | 00000 |
| 3" | 0.0001" to 0.0003" | Rockwell C50 | Not Rated | 1 | 000000000 | 00000 |
Vibration-Resistant Female-Threaded Anchors for Block and Brick
Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration. To install, tap into a drilled hole with a hammer and position your fixture. Then, insert a screw or threaded rod and tighten. Pull-out strength and shear strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
Strength, lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Lg. | Drill Bit Size | Min. Installation Dp. | Dia. | Pull-Out | Shear | Tested In | For Use In | Pkg. Qty. | Pkg. | |
Zinc Alloy | |||||||||||
| 3/8"-16 | 1 3/4" | 11/16" | 1 3/4" | 11/16" | 900 | 960 | 3,000 psi Concrete | Block, Brick, Concrete, Stone | 10 | 000000000 | 000000 |
Hole-Alignment Pins
Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.
For technical drawings and 3-D models, click on a part number.
Double-Taper Hole-Alignment Pins
When one side of these pins wears out, use the other one. They’re also known as barrel drift pins. Use alignment pins to align structural components such as I-beams and angle iron for bolting, riveting, and welding.
For technical drawings and 3-D models, click on a part number.
Body | ||||||||
|---|---|---|---|---|---|---|---|---|
| Point Dia. | Taper Lg. | Dia. | Overall Lg. | Shape | Texture | Material | Each | |
| 5/16" | 2" | 11/16" | 7 1/2" | Round | Smooth | Steel | 000000 | 00000 |
Nonsparking Hole-Alignment Pins
Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant pins inhibit sparking. They satisfy OSHA requirements for nonsparking tools for locations where flammable vapors and combustible residues are present. Nonsparking tools are not, however, classified as antistatic because they do conduct electricity. Use alignment pins to align structural components such as I-beams and angle irons for bolting, riveting, and welding.
Note: Do not use these tools in direct contact with acetylene.
Body | ||||||||
|---|---|---|---|---|---|---|---|---|
| Point Dia. | Taper Lg. | Dia. | Overall Lg. | Shape | Texture | Material | Each | |
| 9/32" | 3 3/4" | 11/16" | 6" | Round | Smooth | Aluminum-Bronze | 0000000 | 000000 |
Double-Taper Nonsparking Hole-Alignment Pins
When one side of these pins wears out, use the other one. Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant pins inhibit sparking. They satisfy OSHA requirements for nonsparking tools for locations where flammable vapors and combustible residues are present. Nonsparking tools are not, however, classified as antistatic because they do conduct electricity. Use alignment pins to align structural components such as I-beams and angle irons for bolting, riveting, and welding.
Note: Do not use these tools in direct contact with acetylene.
Body | |||||||
|---|---|---|---|---|---|---|---|
| Point Dia. | Dia. | Overall Lg. | Shape | Texture | Material | Each | |
| 3/16" | 11/16" | 8" | Round | Smooth | Aluminum-Bronze | 0000000 | 000000 |