Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

These clamps have twice the capacity of standard fast-action bar clamps.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol‐grip handle to lock the clamp in place.

Squeeze the handles to open the clamp; release and the spring holds it tightly in place.

The long, narrow jaws clamp farther into a workpiece and in tight spots.

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.

Turn the knob to adjust the opening size.

Squeeze the handles and the jaws will automatically adjust to fit your workpiece.

Mount to the top of your workbench.

The long, pivoting jaws let you clamp farther into your workpiece and in tight spots.

Clamp thin sheet material together without drilling holes. These clamps open with special pliers and spring closed when the pliers are released.

Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.

Mount the base to a work surface using screws.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Push the lever to lock the handle and prevent accidental opening.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

Push the lever to lock the handle and prevent accidental opening.

Fit the draw arm over a latch plate and pull the handle to clamp.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Push the lever to lock the handle and prevent accidental opening.

Hold workpieces of different thicknesses without adjustment.

Clamp up to three workpieces at 90° angles.

The clamp body is extra-slim to fit into narrow openings.

A bright finish makes these clamps easy to see.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These clamps have twice the capacity of standard C-clamps.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

These clamps are made of stainless steel for excellent corrosion resistance.

Plastic clamping surfaces prevent damage to material.

Hold the workpiece down against a bench or table.

The jaws are rubber coated to prevent damage to pipe and other round workpieces.

A bright yellow vise body stands out on the shop floor.

Use these vises for general purpose workholding.

Quickly install and remove the clamp-on base from a benchtop.

Also known as woodworkers' vises, these mount to the underside of your workbench and sit flush with the surface.

For large workpieces, these vises open three times as wide as standard tilting-head vises. Tilt and lock the head to position work at an angle.

Rotate the head 360° to use three different vise jaws and lock workpieces in position at 45° intervals.

Use the adjustment dials to ensure your work is accurately positioned on X and Y axes.

The vise body and stationary jaw are one piece for high repeatability, even under heavy clamping loads. Ground flat on the base and three sides, these vises ensure accuracy whether mounted on the base, either side, or upright.

Designed for precision grinding and inspection, the construction of these vises ensures workpieces are held perfectly square. They are also known as toolmakers’ vises.

The base and three sides of the vise are ground flat, enabling mounting on its base, either side, or upright.

Reliably hold workpieces with these basic machine vises.

Push the handle to slide the jaw into place for quicker setup than standard drill-press vises.

Designed to hold your part on 4- and 5-axis milling machines, these vises provide rigid clamping while exposing five full sides of the workpiece. This allows even complex parts to be completed in a single operation. You must cut a dovetail into your material before the vise can grip it.

Arrange the pins in a series of holes to grip parts with angled or uneven sides.