Use these cords with computers, lab equipment, and office machines that have IEC connections.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

Power multiple devices from one power source.

Create secure, vibration-resistant connections on both ends—these cord splitters have a hospital-grade plug and locking sockets.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

The threaded ends on these cords seal out contaminants and resist coming loose from vibration in tough industrial environments and automated systems while sending power and signal to devices with M12 connections.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.

Step on or roll carts and platform trucks over these M12 cords without crushing them.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

Connect devices such as computers, printers, and mobile devices.

With Kevlar-reinforced armor, these USB cords stand up to frequent use and bending better than standard USB cords.

Use this general purpose cable to supply power to equipment.

This cable can be stretched by about 40% and return to its original length, making it useful for applications where cable is in motion. It's often sewn into garments or used with equipment that must be worn.

For high-heat applications such as furnaces and ovens, this cable's insulation withstands temperatures of 390° F and higher.

Rated to 12 volts DC, this cable is often used in low-voltage applications such as battery and vehicle wiring and radios. Also known as GPT cable.

Also known as zip cord, this cable is often used in lamps, heat guns, and other small appliances.

Often used to wire pendant switches, this cable hangs from an overhead connection. Also known as bus drop cable.

The insulation has excellent resistance to oil, so this cable can be used near motors. Often used in automated applications, it withstands continuous motion without degrading data or signal transmission

Use this cable without conduit in automated applications—it meets crush and impact requirements for exposed runs in cable carriers, and withstands continuous motion without degrading data or signal transmission.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable. It withstands continuous motion without degrading data or signal transmission.

Bend and flex this silicone-insulated cable in temperatures up to 350° F. It can keep moving in areas twice as hot as most other continuous-flex cables without degrading data or signal transmission.

This cable meets TC-ER crush and impact requirements for exposed runs in cable trays, so it can be used without conduit. It sends signal and data to operate, measure, or regulate automated equipment.

Also known as festoon cable, this flat cable fits in confined spaces such as overhead cranes and hoists. It sends signal and data to operate, measure, or regulate automated equipment.

Nearly two-thirds the diameter of standard control cable, this cable fits in tight spaces. It sends signal and data to operate, measure, or regulate automated equipment.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it in low-current circuits such as intercoms and security systems.

Also known as fixture whips, this cable has locknuts and fittings attached to the protective metal armor to secure it to a knockout. It's often used to connect light fixtures.

This cable is approved for use in vertical shafts and large facilities with multiple levels. It's often used for low-current circuits such as intercoms and security systems.

Connect low-current circuits such as intercoms and security systems to a building's electrical system in single-level facilities.

Hook up thermostats, air-conditioning units, and other low-voltage equipment.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use in critical circuits such as fire alarms and smoke detectors.

Approved for flame resistance, this cable meets Mine Safety and Health Administration (MSHA) standards. The insulation resists abrasion and chemicals.

Often found in older vehicles, this fusible link wire protects a circuit in applications where you can’t use a standard fuse.

Keep spools of vehicle wire in multiple colors on hand.

More flexible than standard wire, this wire is often used for internal appliance wiring and machine tools. Also known as MTW wire.

Keep spools of wire in multiple colors on hand.

This wire meets stringent military specifications for material quality.

Use this wire in high-voltage applications that require 10,000 volts DC or greater, such as in high-power signs and lasers.

Even at 480° F—hotter than some industrial ovens—this wire’s insulation won’t melt.

Run power over rough surfaces—this wire has thick insulation that stands up to wear and tear.

When pulled lengthwise, this unshielded wire extends 40% and then returns to its original length, so it's useful for high-vibration applications.

The thin strands in this wire have better fatigue resistance under repeated flexing than the strands in standard continuous-flex wire, so it will last longer.

Insulated with TPE, this wire won’t break down from oil, coolant, or chemicals, and it carries a strong signal even when repeatedly bent. This makes it great for greasy equipment on automated lines, such as lubricated cable carriers.

Keep multiple colors of wrap wire on hand to color code connections in circuit boards for easy identification.

This wire wraps around a post terminal on a circuit board to make an electrical connection, eliminating the need for soldering.

Also known as photovoltaic (PV) wire, this wire won’t deteriorate from UV light when used outdoors. It’s often used in solar panels.

These connectors allow you to connect USB devices to a circuit board.

These panel-mount adapters have a female USB connection on both ends to join two USB cables.