After extending to full length to provide added reach, this cable retracts and self-coils for tangle-free storage. It's often used with hand tools and other portable devices.

Rated to 12 volts DC, this cable is often used in low-voltage applications such as battery and vehicle wiring and radios. Also known as GPT cable.

A braided bronze armor provides excellent protection against abrasion and other damage. The wires are tin-plated for corrosion resistance, and the insulation resists corrosive chemicals and salt water.

A thick rubber insulation resists cuts and abrasion, so this cable can be pulled over rough surfaces without damaging the wires inside.

Often used in computers, small electronics, and electronic prototyping, this cable is very flexible with small gauge wire to handle tight curves in narrow spaces.

Reduce cable strain caused by equipment hanging from drop-down cable.

Also known as zip cord, this cable is often used in lamps, heat guns, and other small appliances.

This cable meets TC-ER crush and impact requirements for exposed runs in cable trays, so it can be used without conduit. It sends signal and data to operate, measure, or regulate automated equipment.

Nearly two-thirds the diameter of standard control cable, this cable fits in tight spaces. It sends signal and data to operate, measure, or regulate automated equipment.

Also known as festoon cable, this flat cable fits in confined spaces such as overhead cranes and hoists. It sends signal and data to operate, measure, or regulate automated equipment.

The insulation has excellent resistance to oil, so this cable can be used near motors. Often used in automated applications, it withstands continuous motion without degrading data or signal transmission

Use this cable without conduit in automated applications—it meets crush and impact requirements for exposed runs in cable carriers, and withstands continuous motion without degrading data or signal transmission.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable. It withstands continuous motion without degrading data or signal transmission.

With a life span of more than 20 million high-speed flex cycles, this cable lasts twice as long as standard continuous-flex cable. The frequent motion will not degrade data or signal transmission.

The metal armor on this cable acts as conduit to protect the internal wires. It's often used along the exterior of walls to carry power to outlet boxes. Also known as MC cable.

This cable has an uninsulated ground wire that touches the protective metal armor so it can be used for bonding and grounding. It's often used along the exterior of walls to carry power to outlet boxes. Also known as AC cable.

This cable is approved for use in vertical shafts and large facilities with mulitple levels for critical circuits such as fire alarms and smoke detectors.

This cable is approved for use in vertical shafts and large facilities with multiple levels. It's often used for low-current circuits such as intercoms and security systems.

After extending to full length to provide added reach, this cable retracts and self-coils for tangle-free storage. It's often used with low-current circuits such as microphones and headsets.

Often used in radio transmission, network connections, and digital audio feed, this cable transmits audio, video, and data signals.

Use this cable for complex and high-speed data and signal transmission.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to transmit audio, video, and data signals.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. It has an oil-resistant insulation to protect wires as the cable moves from duct to equipment or machinery.

Often used in automated applications that require continuous motion, this cable sends data between computers, servers, and switches without degrading signal transmission.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to send data between computers, servers, and switches.

Approved for flame resistance, this cable meets Mine Safety and Health Administration (MSHA) standards. The insulation resists abrasion and chemicals.

Also known as hook-up wire, this wire is primarily used for wiring electrical panels, lighting, and plant floor equipment.

Keep spools of wire in multiple colors on hand.

Use this wire in high-voltage applications that require 10,000 volts DC or greater, such as in high-power signs and lasers.

Our most chemical-resistant wire—the PTFE insulation protects against most chemicals, solvents, and oil.

Often used in mining applications, treatment plants, and motors, this wire withstands 5,000 volts AC/DC.

Rated to 50 volts AC/DC, this wire is often used in small electronics and robotics. It withstands temperatures of 390° F and greater.

Nearly half the diameter and up to 40% lighter than standard wire of the same gauge and voltage, this wire fits in tight spaces.

The shielding in this wire blocks signal interference from nearby equipment and devices. When pulled lengthwise, it extends 40% and then returns to its original length, so it's useful for high-vibration applications.

Also known as primary wire, this wire meets SAE standards for low-voltage wiring in trucks, boats, trailers, and other vehicles.

Install this wire in conduit and cable trays throughout commercial and industrial buildings. It's also known as branch circuit wire.

Also known as photovoltaic (PV) wire, this wire is often used in solar panels and resists damage from UV light. It withstands 2,000 volts AC/DC.

Often used in automated applications such as robotics, this wire withstands continuous motion without degrading data or signal transmission.

The TPE insulation on this wire resists most chemicals, including oil and coolant, and withstands continuous motion.

Make connections in circuit boards with these short lengths of terminated wire.

Also known as magnet wire, this wire is commonly used in motors, transformers, relays, and other high-speed winding applications.

Designed for indoor applications, these cords are often used to power appliances.

These self-coiling cords stretch to full length and then return to their retracted length for tangle-free storage.

All cords have a country-specific plug to power equipment from international outlets.

Use these cords with computers, lab equipment, and office machines that have IEC connections.

All cords have a country-specific plug on one end and an IEC socket on the other end.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

Plug these cords into fans that have quick-disconnect terminals.

Power devices that require less than 120 volts AC.

To run DC-powered lab and medical equipment from your outlet, add a power cord with the plug style and length you need. These adapters meet strict IEC, UL, or ANSI/AAMI standards for use with medical devices.

Swap the plug to match the outlet of the region you’re in instead of using separate cords for each country. These adapter cords convert AC voltage to power DC electronics.

Hardwire these cords to equipment.

Use these cords in vehicles and other agricultural and construction equipment.

Carry DC power in or out of electronic devices with these cords. All have industry standard barrel-style connections, letting you power electronics from power supplies.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Compatible with Molex connectors, these cords are sized to fit in tight spaces. They're often used in the interior of machines.

Also known as pico cords, these cords are often used with low-current 8 mm proximity and photoelectric switches.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

With a single cord, these splitters join two devices with M12 connectors to a distribution block or I/O module with M12 connectors. Often used with sensors and actuators, they send signals/power to your devices through one connection.

A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

These cords have an M8 connector on one end and an M12 connector on the other.

TPE insulation protects these cords from some of the toughest industrial conditions, including abrasion, coolants, chemicals, UV rays, and weld slag. Use them in areas with welding, machining, and fluctuating temperatures to send signal and power to M12 proximity switches, valves, and other devices.

Often used in automation systems such as conveyors and sorters, these cords have plug and socket ends, so they quickly connect and disconnect for maintenance and do not need to be hardwired.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.

These cords have an oil- and water-resistant insulation and impact-resistant connectors for protection in harsh environments.

Give the connectors on these cords a quarter turn to lock in place.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.

The insulation resists water, oil, and chemicals, so these cords withstand dirty and greasy environments.

The insulation on these cords resists water, so they can be used outdoors.

These self-coiling cords return to their retracted length after stretching for tangle-free storage.

Insulated to resist water, oil, and solvents, these cords withstand dirty and greasy environments.

Designed for indoor use, these cords are often used to power appliances.

Also known as hospital-grade cords, these have extra-tight connections to prevent them from detaching. The connectors are marked with a green dot.

An isolated ground connection on these outlets protects computers and other sensitive equipment from external signals that interfere with the equipment’s performance.

Often used in offices and workstations, these outlet strips power multiple devices from a single wall outlet.

These curved outlet strips clamp onto a pole or table leg.

Bring power to workstations that are not near a wall—these poles mount from the ceiling.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

Install these extra-long strips onto the frame of an electrical cabinet.

Also known as hospital-grade outlet strips, these outlets have an extra-tight fit to prevent plugs from detaching. They are marked with a green dot.

Often used in robotics, packaging, conveyors, and other applications with constant movement and high temperatures, these silicone rubber cords bend and flex at temperatures up to 325° F.

Display video from one source on two different monitors.

Rated IP67, these cords withstand wet and dusty locations, such as enclosures on CNC machines.

With a flange on the socket end, you can mount these cords in a panel cutout to move data between computers, printers, and mobile devices.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs).

Use these cords to extend the distance between your FANUC CRX robot arm and your controller.