Eliminate seal wear and leakage with pumps that use magnets to turn the impeller. They’re often used with electroplating and photographic solutions.

These pumps can be used to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers.

The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Use these pumps to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers

Propel liquid higher and farther than standard circulation pumps. They're commonly used with chillers, heat exchangers, and boiler feed systems.

Instead of a fan-cooled motor, these pumps have an integrated motor that's cooled by the liquid being pumped for virtually silent operation and a long service life. Also known as canned motor pumps, they're commonly used in chiller systems and aquariums.

Use less electricity to achieve the same flow rates as other circulation pumps.

Drain underground tanks and process wastewater with pumps that can be installed up to 20 ft. above your liquid source.

A high-horsepower motor handles four times the flow and twice the pressure of other inline circulation pumps. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Eliminate seal wear and leakage—these pumps have magnets that turn the impeller for a long service life. Install them directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Accommodate performance changes in your system with a three-speed switch that adjusts flow rate. Accommodate performance changes in your system with a three-speed switch that adjusts flow rate. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

Use when space is limited—these pumps connect to a pipe coming from your tank so you can place the pump in another location.

Commonly used in machine tool coolant tanks, these pumps have an intake that can be completely submerged in liquid.

A 316 stainless steel housing sealed with fluoroelastomer resists mild chemicals and acids, such as coolant, oil, and phosphoric acid.

Mount these pumps in any position, even upside down. Pumps have a subfractional horsepower motor rated for intermittent use. Also known as diaphragm pumps, use them for low-flow spraying, draining, and washdown applications.

Also known as gear pumps, these produce a smooth flow of liquid for applications such as cooling engines, powering hydraulic equipment, and extracting liquid from holding tanks.

Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

Resistant to chemicals such as ammonia, detergents, and cleaning fluids, these pumps have a Santoprene diaphragm and polypropylene housing. Pumps can be used to move thick sludges and slurries

A Buna-N diaphragm stands up to lubricating oil such as hydraulic and motor oil. These pumps are designed to handle thick sludges and slurries.

A neoprene diaphragm resists oil and chemicals such as isopropyl alcohol and deionized water. These pumps have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

The Santoprene diaphragm resists cracking for a long service life and stands up to water and chemicals such as ammonium hydroxide. These pumps have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

Also known as sprayer pumps, these provide a smooth, uniform flow for agricultural spraying, soap dispensing, and chemical transferring.

The fluoroelastomer diaphragm withstands higher temperatures than a neoprene diaphragm and has better resistance to fuel such as gasoline and kerosene. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

A neoprene diaphragm stands up to oil and chemicals such as isopropyl alcohol and deionized water. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

With a 316 stainless steel housing and a fluoroelastomer diaphragm, these pumps resist a variety of harsh acids and alkalies, such as phosphoric acid, nitric acid, and sulfuric acid. They have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

These pumps have a bronze housing and gears for use with water. Also known as gear pumps, they produce a smooth flow of liquid for water delivery.

Commonly called rotary vane pumps, they have a built-in bypass relief valve to prevent pressure buildup.

Use these pumps to move lubricating oil such as hydraulic and motor oil. Also known as flexible impeller pumps, they create a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

A chemical- and impact-resistant PVDF housing stands up to aggressive chemicals such as methyl ethyl ketone and xylene.

Pump fuel such as gasoline, kerosene, and diesel fuel.

Use these pumps to move lubricating oil such as hydraulic and motor oil.

A filter/lubricator ensures efficiency and reduces wear on the pump. Often used with hydraulic oil and motor oil in addition to acidic and alkaline liquids, these pumps have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

With a higher pressure than other air-powered drum pumps, these pumps move thick chemicals with a viscosity of up to 5,000 centipoise. A stainless steel housing stands up to acids, solvents, and other caustics.

These pumps have a motor that is rated for IEC Zone 1, Groups IIB and IIA; and IEC Zone 21, Groups IIIC, IIIB, and IIIA hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits.

With wetted parts made of FDA listed materials, these pumps can be used with food, water, and beverage. They have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

Made with PTFE components, these pumps stand up to aggressive chemicals our other drum pumps can't, such as hydrochloric acid, bleach, sodium hydroxide, and methyl ethyl ketone.

Made with polypropylene components, these pumps withstand highly corrosive diesel exhaust fluid while preventing it from crystallizing.

Since these pumps use suction to draw liquid out of your container, they continue dispensing once you get them started.

Remove liquid from hard‐to‐reach areas with a long, flexible intake tube that extends into deep and hard‐to-access tanks.

Designed to move low volumes of caustic liquids in confined areas, these pumps have a thin intake tube and a small handle.

These pumps have a selectable flow rate, so you can adjust flow for different dispensing applications. A lever handle maximizes output with each stroke for low-effort dispensing.

A nozzle and hose allow you to dispense directly into your container. The lever handle maximizes output with each stroke for low-effort dispensing. The handle delivers fluid on both the forward and backward strokes to quickly move drum contents.

Eliminate leaks and waste with a faucet-style nondrip nozzle that quickly starts and stops flow.

Eliminate leaks and waste with a faucet-style nondrip nozzle that quickly starts and stops flow.

These pumps have a discharge hose for transfer applications and a vacuum breaker that drains the hose to prevent siphoning. A lever handle delivers fluid on both the forward and backward strokes for faster dispensing than other drum pumps.

A lever handle delivers fluid on both the forward and backward strokes for faster dispensing than other drum pumps.

A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

These pumps are C-UL listed for use in environments with flammable gases and combustible dust. Operating on a 12-volt battery, use them to transfer and drain fuel such as gasoline, diesel fuel, and kerosene.

Quickly and cleanly transfer oil with no need for an electrical connection, air connection, or manual pumping. These drum pumps come with everything they need to operate.

These pumps are rated for fuel such as gasoline, kerosene, and diesel fuel.

For accurate dispensing in extremely low-flow applications, these pumps allow you to adjust flow in 2% increments.

Designed to move 40 gallons of liquid per minute, these pumps quickly empty drum contents.

These pumps quickly empty drum contents by moving 48 gallons of liquid per minute. Their electric motors are UL listed for use in environments with flammable gases and combustible dust.

Made of PVDF components, these pumps resist harsh chemicals such as hydrochloric acid and sulfuric acid. They have a foot pedal for hands-free operation.

Rated for liquids with a viscosity up to 5,000 centipoise, these pumps can be used with thick chemicals such as electropolishing solutions.

An adjustment dial with a locking lever allows for easy flow control. Also known as diaphragm metering pumps, these can be used with pressures up to four times higher than standard pumps for chemicals.

Automatically control output from a distance using variety of analog and digital signals, including 4-20mA and external pulse signals.

For high-volume chemical sampling and draining, these pumps have a powerful motor that enables them to move 2,448 gallons of liquid per day.

These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

Install these pumps in a panel cutout. Often used in food and beverage, pharmaceutical, and lab applications, they dispense small amounts of liquid at a set rate.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use the handle to carry pumps from job to job.

Complete with a suction strainer and 6 feet of garden hose, these little pumps come ready to clean up small open spaces.

These pumps have an impact-resistant aluminum housing and handle larger solids than other battery-operated water-removal pumps. Use them to remove water from areas without power.

Convenient to keep in your toolkit for on-site cleanup, these pumps attach to your drill for small liquid extraction jobs as well as draining water from clogged sinks and emptying tanks.

Fill the fuel tank with gasoline to remove water at sites without power.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2” in diameter.