How to Prime Your Pump
More
How to Determine Feet of Head
More
About Process Pumps
More
About Sump, Water-Removal, Condensate, and Submersible Pumps
More
Low-Maintenance Plastic Circulation Pumps for Water and Coolants
Eliminate seal wear and leakage with pumps that use magnets to turn the impeller. They’re often used with electroplating and photographic solutions. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.
Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.
Flow Rate, gpm | Intake | Discharge | Overall | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Max. Flow Rate, gpm | @ 5 ft. of Head | Max. ft of Head | Max. Pressure, psi | Max. Viscosity, cP | Temp. Range, °F | hp | Current, A  | Tube Connection Type | Gender | For Tube ID | Tube Connection Type | Gender | For Tube ID | Lg. | Wd. | Ht. | Each | |
120V AC, Single Phase—With Thermal Overload Protection | ||||||||||||||||||
Plug | ||||||||||||||||||
| 6 | 2 | 7 | 3 | 20 | 35° to 150° | 1/50 | 0.9 | Barbed | Male | 5/8" | Barbed | Male | 5/8" | 7 5/8" | 3 1/2" | 5 1/4" | 0000000 | 0000000 |
Submersible Pumps for Salt Water
Circulate salt water in submerged and open-air applications. These pumps use magnets to turn the impellers so there is no shaft seal to wear out. They must be wired to a plug (not included) to activate. Do not run dry.
Max. Flow Rate, gpm | Intake | Discharge | Overall | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| @ 1 Ft. of Head | @ 5 Ft. of Head | Max. Ft. of Head, ft. | Temp. Range, °F | Horsepower | Current, A | Pipe Size | Thread Type | Gender | Pipe Size | Thread Type | Gender | Ht. | Wd. | Dp. | Each | |
120V AC, Single Phase—With Thermal Overload Protection | ||||||||||||||||
Hardwire | ||||||||||||||||
| 5 | 3.8 | 13 | 35° to 130° | 1/50 hp | 0.9 | 3/8 × 3/4 | NPT × NPT | Female × Male | 1/4 | NPT | Male | 4 1/8" | 6 1/8" | 4 7/8" | 00000000 | 0000000 |
Flood Coolant Dispensers with Reservoir
These dispensers have a reservoir for recirculating coolant. They provide a constant flow of coolant, so they dissipate heat more efficiently than mist and droplet dispensers, making them suitable for cooling long machine cycles. Coolant strainers prevent debris from getting into the recirculated coolant.
Maximum flow rate and shut-off height are for water-soluble oil. Shut-off height is the maximum height to which the water-soluble oil can be pumped.
Nozzle | Reservoir | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Cap., gal. | Max. Flow Rate | Max. Pressure, psi | Coolant Outlet Hose Lg. | Lg. | Type | Nozzle Material | O'all Ht. | Wd. | Dp. | Reservoir Material | Shut-Off Ht., ft. | For Max. SSU Viscosity Grade | Voltage | Features | Each | ||
For Use With Coolant, Water | |||||||||||||||||
| A | 1 | 108 gph @ 1 ft. of head | 5 | 6 ft. | 6" | Rigid | Polyethylene Plastic | 9 3/8" | 12" | 6" | Polypropylene Plastic | 11.5 | 100 | 120V AC | Adjustable Flow, Coolant Strainer | 00000000 | 0000000 |