The knurled handle of these punches offers a more secure grip than standard punches. Use pin-removal punches to knock out pins and rivets that have already been loosened.

The rounded tip of these punches fits into the open ends of hollow and spring pins to protect them from damage during removal.

Made of materials that are Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.

A soft brass body minimizes the damage these punches make on work surfaces.

Impact-resistant steel makes these punches stronger and more durable than standard pin-removal punches.

The punches in these sets have a knurled handle, which offers a more secure grip than standard punches. Use them to knock out pins and rivets that have already been loosened.

The rounded tip of these punches fits into the open ends of hollow and spring pins to protect them from damage during removal.

When one side wears out, use the other one. Also known as barrel drift pins.

Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.

Often called bull pins, these pins are designed to resist mushrooming caused by repeated pounding.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

The tapered shaft of these pins eliminates the need for hammering and prying when aligning flange bolt holes.

These punches set grommets that have a standard washer, tooth lock washer, or an extended-neck washer.

Strike the punch with a mallet to set standard fabric snap halves.

Squeeze the adjustable handle to install standard and dual-sided fabric snaps and fabric grommets.

Use these tools to drive the threaded stud into a solid surface.

Contains pin-loosening, pin-removal, and center-marking punches.

Set nails flush or drive them out of view without damaging wood surfaces.

Use these punches to make round holes up to 1" dia. in fabric, leather, and rubber.

Attach two punch heads to the handle at the same time to punch a gasket or washer in a single strike.

Quickly switch between inner and outer punches to create washers faster than with standard sets.

Slide thin sheets of material into the included die block then punch an inner and outer hole to create a shim or washer.

Use these one-piece tools to make round holes up to 1 3/4" dia.

Create holes for installing heavy duty industrial connectors. When the die and punch are pressed together, four centering mandrels in the die mark where to drill holes for the connector's assembly.

Use a wrench to cut DIN-size holes in steel up to 1/16" thick.

Rotate the angled head of the driver up to 180° to fit it into tight spaces and supply eight tons of force to the hole punches.

Punch conduit up to size 1 1/4.

The body is cast steel.

Cut keyways at the edges of existing holes. Also known as a keyway nibbler.

About half the size of a standard portable lever-operated punch, these punches can fit in your toolbox.

Deliver nearly three times the punching force of a standard portable lever-operated punch by holding one handle and turning the other 360°.

Use twice the punching force of standard extended-reach punches to make holes in structural steel channels and angle iron.

Our most powerful lever-operated punch, the rotary-action socket turns to deliver two to three times the punching force of other bench-mount lever-operated punches.

Turn the handle of these punches while pushing down to punch holes in cork and rubber.

Cut through spot welds on sheet metal and make faster, more precise cuts than drill bits and other hole saws.

The carbide teeth on these steel saws cut aluminum, brass, bronze, steel, and plastic sheets and last up to twice as long as high-speed steel teeth.

These saws reduce friction and prevent material buildup when cutting fiberglass and plastic.

Use these saws with a drill press to cut a variety of hole sizes in sheet metal.

The carbide teeth on these saws last up to twice as long as high-speed steel teeth.

Quickly connect these saws to your drill or drill press with the built-in arbor.

The carbide-tipped teeth on these saws last up to twice as long as high-speed steel teeth.

The carbide teeth on these steel saws cut hard metal such as steel, stainless steel, cast iron, and titanium.

The diamond-grit edge on these hole saws cuts more accurately, leaves a smoother finish, and lasts up to twice as long as carbide-grit-coated teeth.

These kits have saws with high-speed steel teeth and a steel body.

Lower cutting depths than standard hole saws make these saws less likely to rip or tear while making smooth, burr-free cuts in sheets.

Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.

These steel stamps are strong enough to make marks on surfaces with a Rockwell hardness up to C50, including stainless steel and heat-treated steel.

Made from 440C stainless steel, these stamps won't rust and flake with exposure to moisture and chemicals. They're strong enough to make marks on surfaces with a Rockwell hardness up to C50, including other stainless steels and heat-treated steel.

Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals.

Create raised lettering similar to a license plate with these reverse-face stamps. Impressions are made on the backside of metals for an embossed character on the front.

Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals. Stamps are steel.

The thick shank provides more control for more consistent marks than our standard metal stamps. Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals. Stamps are steel.

These stamps have a solid face.

Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals.

These stamps have a border around the characters to help them stand out.

Less than 2" wide, these stampes let you choose only the characters you need from 0-9, A-Z, and blank spaces.

Mark surfaces with unique characters for traceability, quality control, and inspection.

These stamps provide an entire number set in the convenience of one handheld stamp. Rotate the wheel to change the character.

Mark keys with common messages such as "Do Not Copy" and "Master".

With an internal spring mechanism, these Starrett punches offer one-hand operation when marking hole centers.

Use the Starrett punches in these sets to mark hole centers in metal and other materials. Also known as center punches.

Also known as center punches, the tools in these sets mark hole centers in metal and other materials.

Made of aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking.