Join two beams in a straight line.

Clamp to both sides of a beam to add an anchor point for hoists and other overhead equipment.

For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.

These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

A toothed clip secures these clamps to the beam—no fasteners required.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Cut as much strap as you need to hang duct, pipe, and other materials.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

These U-shaped supports allows access to pipe and conduit after installation.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

Mount to a surface and add a cable tie to secure a bundle.

Often used to secure vertical running material, these mounts maintain space between a bundle and a surface.

Use these plastic mounts with metal-detector-grade cable ties when detection and retrieval is essential, such as in food processing applications. Mounts are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

Attach with a screw or other fastener.

Quickly attach and detach a bundle.

Route and organize wire, cable, and hose along your DIN rail. Unlike zip ties, these cable ties can be temporarily undone to add or remove material.

Position terminal blocks, relays, and other components mounted to DIN rails with these stops and spacers.

Mount terminal blocks, power supplies, relays, and other control and distribution devices on walls and other flat surfaces and in enclosures.

Protect development boards from dust, water, and debris by mounting them to DIN rails inside control cabinets.

Use these brackets for extra mounting space behind DIN rail to accommodate wiring and bulky items.