When you’re working up high, keep these wrenches secure at your side. Hook their tether ring to a carabiner or lanyard (not included), so they won’t fall to the ground if dropped.

Sealed against dust, dirt, and moisture, these wrenches can be used in greasy machine shops and dusty construction sites.

Also known as rotator ratchets, these wrenches let you rotate the grip to tighten a socket. They're useful when you don't have the space to swing the handle side to side.

Extend the length of these wrenches for more reach—the shaft locks into place at set increments. When it’s time to change your socket, release it with the push of a button.

With no internal screws, these ratchet wrenches don’t have a single small part that could fall into and damage equipment.

No need to pull the socket off the tool—push a button to release.

Pivot the head and extend the handle—these wrenches adapt to reach fasteners in challenging spots. When it’s time to release the socket, just push the button on the back of the head.

Position the head anywhere along the handle.

The ratcheting mechanism turns sockets quickly.

A soft, contoured grip gives you a secure, comfortable hold. Use these handles to tighten and loosen sockets from above when there isn’t room to swing a standard wrench.

Hold the collar in place to position your socket, then rotate the free-spinning T-handle to quickly fasten nuts and bolts.

No need to pull the socket off the tool—push a button to release.

Measure with an accuracy of ±2%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

Built to last, these wrenches have an enclosed steel head that seals lubrication in and dirt, dust, and moisture out to protect the ratchet mechanism. Since they’re air powered, these wrenches turn fasteners more quickly than handheld wrenches.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

Pivot the head to access fasteners from an angle.

Designed to fit on external Torx-Plus fasteners, often found on pickup trucks, these sockets have squared lobes that resist slipping at high torque.

Grip the indentations around the outside of tri-groove fasteners.

The short bit on these sockets fits in spaces where height clearance is limited.

When vertical space is tight or you need an extra twist on your socket, use these dual drive hex bit sockets. They work with a standard square drive tool and a box or open end wrench.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

An extra-long Phillips bit allows these sockets to reach far-away fasteners. Use them where standard or stubby sockets can’t reach.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as Robertson bits.

An opening at the tip of these sockets fits around the security pin, allowing you to drive tamper-resistant Torx Plus screws.

A magnet holds the fastener securely enough to drive self-tapping screws.

Pivot the head to access fasteners from an angle.

Extra-long bits help you access hard-to-reach fasteners.

The short bit on these sockets fits in spaces where height clearance is limited.

A magnet holds the fastener securely enough to drive self-tapping screws.

Keep common extension lengths on hand to reach a variety of spots—just attach them to your socket.

Bend these extensions to reach inconveniently located fasteners. These sets include multiple extension lengths, so you can find the right length to reach around obstructions.

The male ends of these extensions are rounded, so they can pivot to use your tool at an angle.

Convert from one square drive size to another.

Convert your socket into a flex socket to access fasteners from an angle.

Convert your socket into a flex socket without worrying about the adapter falling off.

Turn sockets with a bit screwdriver.

Fit these adapters between a wrench and socket to enable finger tightening.

Lock the adapter on your tool and the socket to the adapter to prevent accidental disengagement.

Attach to your socket for a longer reach.

Reach a variety of spots by keeping common extension lengths on hand.

Pull the collar to quickly attach and remove sockets.

First developed for aerospace and automotive assembly processes, these extensions will stand up to your high-volume production and assembly lines.

Suitable for occasional maintenance work, these sets are imported.

Suitable for occasional maintenance work, these sets are imported.

Grip the indentations around the outside of tri-groove fasteners.

With squared lobes that won’t slip at high torque, all of the sockets in these sets are designed to fit on external Torx-Plus fasteners, often found on pickup trucks.

The short bit on these sockets fits in spaces where height clearance is limited.

In addition to a standard square drive, the sockets in these sets have a hex-shaped base so you can use a ratchet wrench along with an open-end or box wrench for additional leverage.

Tighten or loosen hard-to-reach fasteners with the extra-long bits in these socket sets.

In addition to a standard square drive, the sockets in these sets have a hex-shaped base so you can use a ratchet wrench along with an open-end or box wrench for additional leverage.

When vertical space is tight or you need an extra twist on your socket, use one of the dual-drive Phillips bit sockets in this set.

These sockets are also known as pin-in-Torx bits.

These sockets are made to withstand the high torque and force of impact tools.

Convert from one square drive size to another.

The Torx bit sockets in these sets fasten Torx screws often used in vehicles, bicycles, and electronics.