McMaster-Carr logo
    Filter by
    System of Measurement
    Reamer Diameter
    Flute Type
    Reamer Fractional Size
    Shank Type
    Flute Length
    Sold As
    Number of Flutes
    Reamer Type
    Overall Length
    Reamer Operation
    Spiral Direction
    Recommended Expansion Limit
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    5 Products

    Reamers
    3D CAD models available

    Finish holes to precise inch, metric, wire gauge, or letter sizes with these reamers.
    Round Shank
    These reamers fit in the chuck of drill presses, turret lathes, and other machine and power tools, making them the most common shank type.
    Straight Flute—The most common flute style, these reamers are suitable for a wide range of applications, but not recommended for holes with a keyway or other breaks in the surface.
    Spiral Flute—Since these reamers clear chips better than straight flutes, they leave holes with a smoother finish. They're better for holes with breaks in the surface, such as a keyway, because they cut continuously across the breaks instead of moving in and out.
    High-Speed Steel—Durable and wear resistant, these are good for general purpose reaming in most materials.
    Cobalt Steel—With better heat and wear resistance than high-speed steel, these reamers run up to 25% faster, last longer, and perform better on hard materials, such as cast iron, hardened steel, titanium, and stainless steel.
    Carbide-Tipped Tool Steel—Since these reamers retain a sharper, harder edge at higher temperatures than high-speed steel and cobalt steel, they can be used on hard materials, such as iron, hardened steel, and steel alloys. They aren't as brittle as solid carbide reamers, so they can be used in less rigid setups, such as a hand-held drill.
    Right-Hand Spiral—These reamers pull chips upward as they cut, so they're often used in blind holes.
    Lg.
    Reamer Dia.
    Material
    Flute
    Overall
    No. of
    Flutes
    Spiral
    Direction
    Cutting Dia.
    Tolerance
    For Use On
    Each
    Straight Flute
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers, Round Shank, Straight Flute.
     
    Inch
    0.5313" (17/32")High-Speed Steel2"8"8__0" to 0.0003"Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel0000000000000
    0.5313" (17/32")Cobalt Steel2"8"6__0" to 0.0003"Aluminum, Brass, Bronze, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel, Hardened Steel000000000000
    0.5313" (17/32")Carbide-Tipped Tool Steel2"8"6__0" to 0.0003"Aluminum, Brass, Bronze, Fiberglass, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel, Hardened Steel000000000000
     
    Spiral Flute
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers, Round Shank, Spiral Flute.
     
    Inch
    0.5313" (17/32")High-Speed Steel2"8"6Right Hand0" to 0.0003"Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel000000000000
     
    Expandable Flutes, Round Shank
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers, Expandable Flutes, Round Shank, Straight Flute.

    Straight Flute

    Unlike standard reamers, which are unusable once they become worn, these can be returned to their original size for finishing holes. After the reamer is worn down, tighten the set screw to expand the diameter, grind the reamer to its original size, and get back to work.
    These are not designed for producing holes larger than the listed diameter or for producing holes of various sizes. The set screw should not be loosened.
    These reamers fit in the chuck of drill presses, turret lathes, and other machine and power tools, making them the most common shank type.
    Straight Flute—The most common flute style, these reamers are suitable for a wide range of applications, but not recommended for holes with a keyway or other breaks in the surface.
    Carbide-Tipped Tool Steel—Since these reamers retain a sharper, harder edge at higher temperatures than high-speed steel and cobalt steel, they can be used on hard materials, such as iron, hardened steel, and steel alloys. They aren't as brittle as solid carbide reamers, so they can be used in less rigid setups, such as a hand-held drill.
    Lg.
    Reamer Dia.
    Material
    Flute
    Overall
    No. of
    Flutes
    Cutting Dia.
    Tolerance
    Recommended
    Expansion
    Limit
    For Use On
    Each
    Straight Flute
     
    Inch
    0.5313" (17/32")Carbide-Tipped Tool Steel1"8"60" to 0.0003"0.010"Aluminum, Brass, Bronze, Fiberglass, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel, Hardened Steel0000000000000
     
    back to top