Use these connectors in general purpose residential and commercial applications.

Eliminate the need for wire stripping; snap-on terminals pierce the wire insulation and grip the wire securely. Access the wire connection by opening the hinged housing.

Visually confirm that connectors have power; they have an indicating light that is visible from any angle.

Rated NEMA 6P and 13, IP66, and IP69K when mated, connectors withstand oil/coolant spraying, high-pressure, high-temperature washdowns, and are corrosion resistant so they can be used in marine environments.

Visually confirm that sockets have power—the face lights up when they're connected. The rubber housing protects them from damage caused by drops and other impact.

When mated, connectors meet NEMA 6P, NEMA 12, and either IP67 or IP69K.

Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch.

Use these general purpose connectors indoors in high vibration applications. A quarter turn locks them together when mated to remain secure in high-vibration applications.

A good fit for tight spaces, these connectors are also known as NEMA midget plugs. They turn to lock together when mated to prevent accidental disconnection.

When mated, these connectors meet NEMA 6P for protection against washdowns and temporary submersion.

Stainless steel hardware and nickel-plated blades or slots protect connections from damage in corrosive environments. These connectors turn to lock together when mated to prevent accidental disconnection.

A quarter turn locks these connectors in an outlet to remain secure in high-vibration applications and prevent accidental disconnection. They are not compatible with NEMA configurations.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.

Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.

Connect and disconnect with the power on—spring-loaded contacts open like a switch when separating the connectors, preventing an electrical arc.

These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.

Configure a connector for your application by combining housings with pins and sleeves for different wire sizes. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Made with industry standard barrel-style ends, these connectors carry DC power between electronic devices and power supplies.

Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Quickly mate these connectors by pushing them together. They're often used with 12 mm proximity switches and valves in automated systems.

Screw these micro M16 connectors together to securely connect equipment.

Install these connectors directly onto circuit boards to carry DC power from a power supply to your device. The industry standard barrel-style ends, which are often found on power supplies for laptops, wireless routers, and other common electronics.

Connect wires to circuit boards with Molex Mini-Fit push-in connectors. A locking tab holds the housing and plug together once they’re mated.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

Reduce the likelihood of slips and falls in high-traffic areas—connectors won't roll when stepped on.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

A current rating up to 400 amps makes these connectors suitable for use in industrial machinery and floodlights.

These connectors allow you to connect USB devices to a circuit board.

Your standard light switches—these switches stick out of your mounting surface and flip on and off.

Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control lights on the same circuit. They're also known as three-way and four-way switches.

Similar to a seesaw, these switches have an actuator that pivots when pressed to turn them on or off.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit.

Control lights by transmitting a wireless signal from these switches to a control relay on your fixture.

Secure sensitive lighting equipment; these switches have a round key that is difficult to duplicate.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit.

Flat and completely smooth, these switches are easy to wipe down. With just a light tap, you can switch lights on and off, even if you’re wearing gloves.

Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control the brightness of lights on the same circuit. They're also known as three-way switches.

Automatically turn outdoor lights on and off based on lighting conditions to conserve energy.

Also known as occupancy sensors, these controls turn lights on when movement is detected and off when an area is empty. They fit standard wall plates.