Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation. No need for a permit—these lights don't require opening the space above the ceiling. They connect to standard housings with the included springs and cables. Just remove the old lens, bulbs, drivers, and their wiring before installation. DLC (DesignLight Consortium) listed, these lights have been tested to confirm their energy efficiency. They’re also ETL listed for use in damp locations.

Adjust the light appearance and brightness to match your existing lighting. The frosted lens disperses light evenly to prevent glare on equipment.

Link these lights together to create different shapes with a sleek look. Also known as slot lights, they’re often found hung from, mounted to, or recessed into ceilings in offices and cafeterias. Any shape you form will be lit up continuously because the L, tee, and X connectors (sold separately) light up. Straight connectors (sold separately) link two lights together from the inside. There’s no need for tools for any connections. Remove the end panels, push together the electrical cables, and snap the light in place. You can link up to 32 feet of lights together with a single power connection. These lights include all necessary hardware for mounting.

Choose between a warm or neutral light appearance on the power supply to match existing lights. Each LED is inspected to make sure there are no visible differences in temperature and brightness, so you can combine multiple lights within the same space.

Suspension lights can send up to half their light upward to reduce glare, prevent eye strain, and make your space appear larger. Use them against a white ceiling for the best effect.

These fixtures disperse light from the top, bottom, and side to produce ambient lighting. They mount to the wall so they're often used in enclosed spaces such as stairwells, hallways, and storage rooms. Rated for use in damp locations, these lights withstand humidity and moisture. They have built-in LEDs, which last longer, are more efficient, and generate less heat than fluorescent lights. The lens is smooth and frosted to disperse light evenly. They can be hardwired to operate on any of the voltages listed.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs. With built-in LEDs, these lights last longer, are more efficient, and generate less heat than other light technologies. Use the switch on the power supply to choose between warm, cool, or neutral light—no more mismatched lights. All have passed strict U.S. and Canadian safety standards.

Mount these lights in recessed spaces so the lens is flush with the ceiling or wall. NEC Classes I and II, they’re safe to use in paint spray booths, blast booths, and other areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

LED lights have a cool light appearance that highlights white and blue tones for high visibility. They are lighter and easier to install than fluorescent lights, and you never have to change a light bulb. They’re UL rated for wet locations, so they’re sealed against humidity and dripping, splashing, and falling liquids.

Fluorescent lights have an access door in the back, so you can mount them in the wall of a paint spray booth and change the bulbs from outside of the booth.

To keep contaminants from entering your clean room, these lights seal against drop ceilings with an airtight gasket. They’re also covered in an antimicrobial paint and are fully enclosed. What makes them great for clean rooms also makes them great for washdowns and food preparation areas. They’re rated NSF/ANSI 2 for splash zones, so you can use them around splashing liquids from food. Rated IP65, they’re sealed against humidity and low-pressure washdowns. You can install these IC-rated lights in direct contact with insulation without risking a fire. Their lens disperses light evenly.

ISO class 3 lights have a prismatic lens that casts a beam that covers a wider area and limits glare better than lights with a smooth lens. If you don’t have a drop ceiling, no problem—these lights will also install into any finished ceiling opening with the built-in clamping arms.

Neutral lights are often used in workspaces. Cool lights highlight white and blue tones for higher visibility than neutral lights.