Fine-tune the size of the laser dot. This laser is sized for mounting on machinery to ensure tools are properly positioned. You can also use it in conjunction with machine-vision cameras to serve as a reference location for making measurements. Laser light is red and is best viewed indoors.

With a sealed lens and an IP67 rating, these lasers are dust and liquid tight, so you can mount them to machines in dusty or wet areas such as labs, warehouses, or marine environments to align components.

Red lasers are best for indoor environments because they’re dimmer than green lasers.

Position these lasers at the correct angle for your job with adjustable angle mounts. They allow 360° rotation.

Use magnetic mounts to attach these lasers to machines and other steel surfaces instead of drilling holes and bolting them. They hold lasers at a fixed angle, but you can combine them with adjustable angle mounts for 360° rotation.

Slip this laser into your pocket so it's on hand to align belts, pulleys, chain, and sprockets. Place the tool against the side of your pulley or sprocket and project the laser onto the included target to detect angular or offset misalignment. They mount magnetically, so you don’t need any fasteners to secure them. The surface of the laser is machined, so it sits flush against flat surfaces for easy and precise alignment. They’re powered by a disposable battery, so they’re portable.

Style B lasers have a threaded tip, so they’re compatible with converters that change the shape of the laser, so you can perform a variety of tasks with the same tool.

Check that your pulley, gear, or sprocket system is properly aligned. These magnetic lasers stick to equipment made of steel. Project the laser beam down your belt or chain and look to see how it hits the target—you can determine angular and offset misalignment at the same time. The target has a machined surface that sits parallel to the contact surface for precise alignment. Adjust your setup until the laser line overlaps with the reference line on the target. These lasers are portable and battery powered, so they’re easy to use in spaces without outlets.

Red lasers are best for indoor environments, since they’re dimmer than green lasers.

Lasers with one adjustable target have a single laser line that indicates offset and angular misalignment. A mirror on the target reflects the laser back to the transmitter’s reference line to show misalignment. No need to fuss with the traditional multi-target method.

Lasers with a built-in LED flashlight provide light in dim areas.

Position these lasers directly on a flat surface. Lasers project a red dot that is best viewed indoors. Twist the knob to focus the dot so it is more precise at short distances.

These lasers take aligning rollers from the traditional multi-tool, multi-person job to a one-tool, one-person job. Strap the transmitter to the roller you want to match and the receiver to the roller you want to check. Instead of aligning with lots of trial and error, these tools have a horizontal beam that shows if your rollers are aligned in the same plane, and a vertical beam that shows if the rollers are evenly spaced along their length. Simply adjust the roller until the beams line up with the tools' reference points.

In addition to being easy to use, these lasers were also designed to be useful in most roller setups. The adjustable straps allow you to secure them to different roller sizes and materials. They're also compact enough to fit in tight spaces between rollers.

Red lasers are best viewed indoors, since they’re dimmer than green lasers.

Green lasers appear up to 10 times brighter than red lasers, so they’re easier to see outdoors or in bright indoor lighting, as well as from far away.

Twist the head to switch between a dot, a horizontal line, or a vertical line. These lasers project accurate level references onto walls, ceilings, and equipment. The laser is red and is best viewed indoors.

When a single point of reference is enough, use a dot. Lines give you an extended reference, so you can level several objects without moving the laser. For stability, mount these lasers to a tripod (sold separately), or attach the magnetic base to a metal surface.

Lasers with straps can also be secured to nonmagnetic surfaces.

Project accurate level references onto walls and ceilings to hang light fixtures or install pipe. These lasers have four vials to verify the level, plumb, and square reference points are accurate. Because they’re red, the lasers are best viewed indoors. They have a screw-on mount to secure to a tripod, or you can use the magnetic base to stick them to equipment for quick checks. A V-groove on the body creates stability on curved surfaces, such as pipe or conduit. They’re powered by disposable batteries, so they’re portable and easy to use when you’re not near an outlet.

Verify your installation is level using a single reference point. These green lasers appear up to 10 times brighter than red lasers for visibility from farther away and in brightly lit areas, including outdoors. Five bubble vials confirm level, plumb, and a specific angle. One vial is a pitch gauge, which shows slope in 1/8" increments to help check drainage. For quick and easy mounting, these levels have a magnetic base. It's strong enough to hold even on vibrating equipment.

Stick these levels to most metal surfaces to mark a dot up to 500 feet across your plant. They’re often used for long range applications, such as laying out conveyors and aligning ventilation systems. The single laser dot gives you a simple check that your installation is level against one reference point. These levels are compact, portable, and have a long battery life. Mount them to rotating equipment without worrying about power cords.

Red lasers are dimmer than green lasers, so they’re best viewed indoors.

Use a leveling plate for mounting the laser to a tripod, or placing it on a surface. The plate has three adjustable legs to level the laser.

90° beam splitters convert one dot into two dots set at a 90° angle.

Dot-to-line converters change the dot into a vertical or horizontal line.

These kits include a laser, a beam splitter, and a leveling plate. Mark a dot up to 1,000 feet across your plant for long-range applications such as laying out conveyors and positioning ventilation systems. A single laser dot gives you a simple way to check that your installation is level. These levels are compact, portable, and have a long battery life. You can mount them to rotating equipment without worrying about power cords. The beam splitter converts one dot into two dots that are set at a 90° angle. Use the leveling plate to steady lasers on uneven surfaces or to mount them to a tripod. These plates have three adjustable legs that stabilize the laser.

Red lasers are best used indoors, since they’re dimmer than green lasers.

Dot-to-line converters change the dot into a vertical or horizontal line.

Mark a dot up to 100 feet across your plant for long-range applications such as laying out conveyors and positioning ventilation systems. The single laser gives you a simple reference point to check that your installation is level. These levels are compact, portable, and have a long battery life.

Red lasers are best used indoors, since they’re dimmer than green lasers.

Add a leveling plate to steady lasers on uneven surfaces or to mount them to a tripod. These plates have three adjustable legs that stabilize the laser.

90° beam splitters convert one dot into two dots set at a 90° angle.

Dot-to-line converters change the dot into a vertical or horizontal line.

These conspicuity tape kits contain everything you need to meet D.O.T. requirements for marking a truck or trailer. Tape withstands power washing.

Use color to identify equipment, materials, and documents at a glance.

For technical drawings and 3-D models, click on a part number.

Easily peel these labels off when they’re no longer needed. Use them for color coding to identify equipment, materials, and documents at a glance.

For technical drawings and 3-D models, click on a part number.

Direct traffic in low-light conditions.

Use these dots to direct traffic in your facility.

Thicker than other floor marking dots, use these abrasion-resistant dots in high-traffic areas.

These shapes can be written on with a wet erase marker (sold separately) and wiped clean with a damp cloth.

The round sponge tip allows you to apply large, clear marks with ease—even on moving objects such as boxes on a conveyor. These markers work best on clean surfaces.