These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

Turn the knob to adjust how much these valves will open or close when actuated. They are often used in irrigation and landscaping applications.

Designed for controlling single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Use with coolant and detergent such as ethylene glycol or soap solutions.

Reduce your pipeline footprint with these low-profile valves that are about half the size of standard valves for coolant.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

Built to withstand the extreme cold of liquid nitrogen and liquid oxygen, these valves are cleaned and bagged for high-purity applications.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

For applications sensitive to contamination, these valves stop flow without contacting the process media by pressing down on the outside of tubing.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

For general purpose applications with water, oil, and inert gas.

Their ball valve design allows these valves to handle three times the flow of butterfly valves.

Slide copper pipe into the solder-connect fittings on these valves and weld for a strong, permanent connection.

All valves have threaded NPT connections.

Use these valves to safely transfer fuel and oil.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

The motor on these valves can handle diverting applications with high flow rates and pressures. They operate on electricity to automatically divert flow between ports.

These valves operate on electricity to automatically divert flow between ports. Use with water, oil, air, and inert gas.

Control flow with an electrical signal.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Use a single valve to create motion and control the speed of that motion.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

Designed for use in dust-collection systems, these diaphragm valves periodically burst air to knock debris from filters.