We will reply to your message within an hour.
More
Also known as machinery eyebolts.
Also known as nut eyebolts, these are designed for through-hole applications.
Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.
The matte black-oxide finish won't reflect light, allowing the eyebolts to blend into the background.
These eyebolts retain their strength in temperatures as low as -40° F.
Route wire and cable through the smooth eye without snagging.
Create your own lifting eye by adding an eye nut to a stud or bolt.
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.
Choose these hoist rings when you need to lift your load from the side.
For a more secure hold than standard hoist rings, weld these hoist rings to your load.
Remove the shackle after lifting while keeping the base installed for future use.
The ball bearing on these hoist rings makes it easy to rotate your load even after it’s suspended.
Keep on hand all the parts needed to assemble custom hoist rings.
With three different thread sizes, these hoist rings are useful when you need to lift different types of equipment.
An indicator dot changes from red to black when these hoist rings are properly tightened, eliminating the need for a torque wrench.
The fixed base provides added stability and allows you to lift heavy loads with smaller thread sizes.
Easily slip these hoist rings in and out of threaded holes by pushing the button to retract their threads.
Also known as master and sling links, a large inner diameter provides room to attach multiple connectors or legs on a sling.
Limit rope and chain movement with the narrow end of these links and attach multiple connectors to the wide end.
Use these links for general lifting applications.
Providing better load distribution and alignment than single oblong links, these reduce wear in three and four leg slings.
Once secured with the included locking pin, these links must be cut off to be removed.
The flat side lets webbing and strapping lay flat, so they don’t slide and bunch.
The wide end of these links has more room for attachments than standard figure-eight links.
Hammer the pin through the center to assemble these links. They’re also known as hammer locks and sling links.
Smaller than lifting oblong links, these links provide room for snaps, carabiners, and other non-lifting connectors.
The flat side allows you to connect webbing and strapping, so they lay flat and resist bunching.
Hang, pull, and secure loads. These rings are good for general non-lifting applications.
Often used with transport chain, these links are good for binding, tying down, and pulling loads.
Restrict rope and chain movement with the narrow end, attach multiple connectors to the wide end, and then hammer these links closed.
Adjust the position of a fitting or an object under load and minimize twisting and knotting.
Use these to adjust the position of a fitting or an object under load and minimize twisting and knotting.
Rotating for easy positioning before a load is applied, these minimize twisting and knotting of rope and chain.
These rotate for easy positioning before a load is applied to minimize twisting and knotting of rope and chain.
A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens.
Rotating for easy positioning before a load is applied, these have a latch to ensure that rope, chain, and fittings won't separate from the hook when the load slackens.
A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens. The hook opening accommodates large anchor points and allows chain to move freely through the closed hook.
The opening on these hooks fits large anchor points and allows chain to slide through when the hook is closed. They have a spring latch to ensure rope, chain, and fittings won't detach from the hook when the load slackens.
Garolite insulation prevents electrical current from passing to hoists and other lifting equipment, causing damage. Because they're electrical insulating, these hooks are often used to hold a workpiece while welding.
Insert in eyes, links, rings, and other connectors with small openings. Also known as J-hooks.
The flat eye on these hooks keeps webbing and strapping flat, so it doesn’t bunch.
Use these on thick molds, castings, and objects that don't have attachment points. Also known as foundry hooks.
For a more secure connection than standard hooks, these hooks have a latch that locks closed when a load is lifted. A ball-bearing swivel allows them to rotate under a load.
For a more secure connection than standard hooks, the latch locks closed when a load is applied.
These rotate for easy positioning before a load is applied.
With a narrow opening and contoured sides, these securely hold a single link of chain to prevent overtightening when lifting a load.
A spring-loaded pin ensures chain won't separate from the hook when the load slackens. Connect your chain to the eye end.
These have a latch that locks closed when a load is applied for a more secure connection than standard hooks. They rotate for easy positioning before a load is applied.
Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the eye end.
Attach chain to the eye end of these hooks.
Often used in binding and tie-down applications, these securely hold a single link of chain.
These swivel hooks have a latch that ensures rope, chain, and fittings won't separate from the hook when the load slackens.
Pull the collar to release the shackle from its locked position.
Disconnect by pulling the lever or attach rope to the eye on the lever for remote release.
Attach a rope to the ring on the pin for remote release where access in limited. These shackles have an eye end for connecting to a hook.
Feed the wire rope into the opening at the bottom of these eye-end fittings and through the body for a quick and simple installation.
Add an eye-end to wire rope without having to fray the rope or use a compression tool.
Also known as socket-end swage fittings, install these eye-end fittings with a roller swage press for a strong, permanent hold.
Install these eye-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.
Compress the thin shank wall with a hand tool to attach these light duty eye-end fittings. They are also known as hand swage fittings.
Also known as pad eyes, these rigid rings provide a strong, fixed anchor point.
The ring pivots 180° to secure loads in various directions. Also known as lashing rings.
Accommodate ties in any direction with these rings that swivel all the way around and pivot 180°.
The ring pivots 90° or 180° to secure loads in various directions.
Accommodate ties in any direction with these rings that swivel all the way around.
Dimples hold the base tight to prevent it from swiveling.
These rings mount flush and fold down when not in use to eliminate obstructions.
Large holes in the base allow adhesive to flow through.
Use these rings to make a temporary anchor point on ferrous metal surfaces.
Adhesive on the back holds these rings in place.
Clamp around a pipe or tube to guide rope.
Use these guides to position a rope.
The ratcheting handle on these load binders tightens incrementally for maximum tension and releases loads without kickback.
These rings pivot to secure loads in various directions.
Also known as Type 3 slings, the eyes lie in a flat position for easy removal from beneath loads.
Slings are reinforced for additional abrasion resistance.
Increase the life of slings by positioning these protectors over areas prone to wear.
Also known as cargo slings, these wide slings provide extra stability and balance when lifting bulky loads.
Slings have plastic-coated fibers woven into the edges for added abrasion resistance.
Also known as Type 5 and endless slings, these slings last longer than other web slings with eyes because they can be rotated to change the load-bearing point.
Also known as Type 4 slings, the eyes are turned 90° so they can form a choker configuration more easily than with flat-eye slings.
Securely hook these slings to a load that has lifting eyes.
Designed for use in the choker configuration, the end fittings keep these slings correctly positioned during use.
These slings are more abrasion and cut resistant than web and round slings, yet lighter in weight than mesh and chain slings.
These slings attach quickly and securely to loads with lift attachments.
Made of abrasion- and chemical-resistant Dyneema, these slings are a lightweight alternative to wire rope slings.
Similar to a finger trap, the loop adjusts freely when loose and holds tight when tension is applied.
Made of galvanized steel mesh to be more cut and abrasion resistant than web or round slings, yet maintain the flexibility to conform to a load.
Also known as Type 3 slings, the flat eye on each end allows the sling to quickly change into the choker, vertical, or basket configuration.
Latching hooks allow you to quickly release a load.
Adjust the chain length and number of legs without changing slings.
Prevent accidental opening of the hook with these locking hooks.
Grab hooks can securely hold onto a single link of chain to shorten a leg or create loops.
These slings have nylon strips sewn into the sleeve to slow deterioration, making them three times more abrasion resistant than other round slings.
Also known as Type 5 and endless slings, these slings last longer than slings with eyes because they can be rotated to change the load-bearing point.