About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
Ultra-Quiet Threaded Track Rollers
The soft rubber or plastic surface on these rollers creates less noise than the metal surfaces found on other track rollers. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.
Nylon-coated rollers have a nonconductive roller surface and are more chemical resistant than urethane-coated rollers. They are permanently lubricated.
Ball bearings create less friction than needle roller bearings, so you can run them at higher speeds.
Thrust-Load-Rated Threaded Track Rollers
These rollers are rated to handle radial and thrust (top and side) loads simultaneously. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers are permanently lubricated and have end seals to retain lubricant and protect rolling elements from dirt and contamination.
Roller | Stud | Thread | Shoulder | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
Steel Flat Rollers with Seal | ||||||||||||||||
| 2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 6,000 | 1,600 | 1,400 | 910 | 225° | Ball | Mounting Hardware | 0000000 | 000000 |
| 2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 6,000 | 1,700 | 1,300 | 910 | 325° | Ball | Mounting Hardware | 0000000 | 000000 |
| 2 1/4" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 6,000 | 1,600 | 1,400 | 910 | 225° | Ball | Mounting Hardware | 0000000 | 00000 |
| 2 1/2" | 1 5/8" | 1" | 2 1/4" | 1"-14 | 1 1/2" | 1 1/4" | 1/16" | 6,000 | 1,700 | 1,300 | 910 | 325° | Ball | Mounting Hardware | 0000000 | 000000 |
| 2 1/2" | 1 5/8" | 1" | 2 1/4" | 1"-14 | 1 1/2" | 1 1/4" | 1/16" | 4,000 | 2,200 | 1,900 | 1,300 | 225° | Ball | Mounting Hardware | 0000000 | 00000 |
Thrust-Load-Rated Corrosion-Resistant Threaded Track Rollers
These rollers are rated to handle radial and thrust (top and side) loads simultaneously. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers are permanently lubricated and have end seals to retain lubricant and protect rolling elements from dirt and contamination.
440C stainless steel rollers are harder and more wear resistant than 303 stainless steel rollers.
Roller | Stud | Thread | Shoulder | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
440C Stainless Steel Flat Rollers with Seal | ||||||||||||||||
Hex Stud End Drive | ||||||||||||||||
| 2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 6,000 | 1,500 | 1,300 | 1,000 | 225° | Ball | Mounting Hardware | 0000000 | 0000000 |
Threaded V-Groove Track Rollers
Thread the stud directly into a component or secure with a nut for through-hole mounting. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Also known as cam followers, track rollers support loads while guiding and positioning work. All rollers are permanently lubricated.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
Roller | Stud | Thread | Shoulder | Groove | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Includes | Each | |
Steel V-Groove Rollers with Seal | ||||||||||||||||||
| 3 1/2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 1 1/4" | 5/8" | 4,000 | 2,200 | 1,900 | 1,400 | 225° | Ball | Mounting Hardware | 0000000 | 0000000 |
Threaded V-Groove Track Rollers with Adjustable Shoulder
Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Secure the stud with a nut for through-hole mounting. All rollers are permanently lubricated.
Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.
Roller | Stud | Thread | Shoulder | Groove | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Includes | Each | |
Steel V-Groove Rollers with Seal | |||||||||||||||||
| 3 1/2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/64" | 1 1/2" | 1/16" | 1 1/4" | 5/8" | 4,000 | 2,200 | 1,900 | 1,300 | 225° | Mounting Hardware | 0000000 | 0000000 |
Flanged Threaded Track Rollers
Thread the stud directly into a component or secure with a nut for through-hole mounting. The flange provides guidance and helps the roller stay on track. All rollers are permanently lubricated and have end seals to retain lubricant and protect rolling elements from dirt and contamination.
Stainless steel rollers offer increased corrosion resistance over steel rollers.
Roller | Stud | Thread | Shoulder | Flange | Static Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | OD | Thick. | Max. Speed, rpm | Radial | Thrust | Max. Temp., °F | Includes | Each | |
440C Stainless Steel Flat Rollers with Seal | ||||||||||||||||
Ball Bearing | ||||||||||||||||
| 2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 2 11/16" | 19/32" | 6,000 | 1,000 | 740 | 225° | Mounting Hardware | 0000000 | 0000000 |
| 2 1/2" | 1 5/8" | 1" | 2 1/2" | 1"-14 | 1 1/2" | 1 1/4" | 1/16" | 3 3/16" | 19/32" | 6,000 | 1,000 | 740 | 225° | Mounting Hardware | 0000000 | 000000 |
Steel Flat Rollers with Seal | ||||||||||||||||
Ball Bearing | ||||||||||||||||
| 2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 2 11/16" | 19/32" | 6,000 | 1,600 | 910 | 225° | Mounting Hardware | 0000000 | 00000 |
| 2 1/4" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 2 15/16" | 19/32" | 6,000 | 1,600 | 910 | 225° | Mounting Hardware | 0000000 | 00000 |
| 2 1/2" | 1 5/8" | 1" | 2 1/4" | 1"-14 | 1 1/2" | 1 1/4" | 1/16" | 3 3/16" | 19/32" | 4,000 | 2,200 | 1,300 | 225° | Mounting Hardware | 0000000 | 000000 |
Double-Flanged Track Rollers
A dual-flange design provides guidance on both sides and helps these rollers stay on track. They handle both radial and thrust (top and side) loads. All rollers are permanently lubricated and have end seals to retain lubricant and protect rolling elements from dirt and contamination.
Roller | Stud | Thread | Shoulder | Flange | Groove | Static Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Lg. | Dia. | Lg. | OD | Thick. | Wd. | Dp. | Max. Speed, rpm | Radial | Thrust | Max. Temp., °F | Bearing Type | Each | |
Steel Flat Rollers with Seal | ||||||||||||||||||
| 2" | 1 5/8" | 7/8" | 2" | 7/8"-14 | 1 1/8" | 1" | 1/16" | 2 11/16" | 17/32" | 9/16" | 11/16" | 6,000 | 1,600 | 910 | 225° | Ball | 000000 | 0000000 |
| 2 1/2" | 1 5/8" | 1" | 2 1/4" | 1"-14 | 1 1/2" | 1 1/4" | 1/16" | 3 3/16" | 17/32" | 9/16" | 11/16" | 4,000 | 2,200 | 1,300 | 225° | Ball | 000000 | 000000 |
Track Rollers
Use these rollers as replacements on an existing door hanger or as the starting point for a customized hanger. Choose rollers that fit the inside width or diameter of your door track.
Rollers with ball bearings travel more smoothly and quietly than rollers with roller bearings.
Plastic bearings are quieter and more corrosion resistant than steel bearings. The plastic is self-lubricating to help bearings travel smoothly. Steel bearings are stronger and more durable than plastic bearings.
Rollers with an eyebolt mount pivot if doors or curtains sway to reduce stress on your track. Attach them to doors with bolts, S-hooks, or shackles.
Rollers with an unthreaded-hole mount have a horizontal plate with a hole. Add a bolt or a mounting plate to attach a door.