11mm Wide Rollers | McMaster-Carr

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Rollers with seal have end seals to protect rolling elements from dirt and contamination.

Track lubricators reduce friction and wear without shutting down equipment. Oil-infused resin distributes lubricant onto rollers, which transfer it to your track.

Metric

Track Rollers
Roller, mm		Stud, mm		Thread			Shoulder, mm			Radial Load Cap., lbs.							Roller-Mount Track Lubricators
Dia.	Wd.	Dia.	Lg.	Size	Pitch, mm	Lg., mm	Dia.	Lg.	Max. Speed, rpm	Static	Dynamic	Max. Temp., °F	Bearing Type	Includes		Each		Each
Black-Oxide Steel Flat Rollers without Seal
16	11	6	16	M6	1	9	11	0.6	19,500	500	750	250°	Needle Roller	__	00000000	0000000	0000000	000000
19	11	8	20	M8	1.25	11	13	0.6	10,500	1,100	1,500	250°	Needle Roller	__	00000000	000000	0000000	00000
Black-Oxide Steel Flat Rollers with Seal
16	11	6	16	M6	1	9	11	0.6	19,500	500	750	250°	Needle Roller	__	00000000	00000	0000000	00000
19	11	8	20	M8	1.25	11	13	0.6	10,500	1,100	1,500	250°	Needle Roller	__	00000000	000000	0000000	00000
Black-Oxide Steel Crowned Rollers with Seal
16	11	6	16	M6	1	9	11	0.6	13,000	500	1,300	250°	Needle Roller	__	00000000	000000	0000000	00000
19	11	8	20	M8	1.25	11	13	0.6	10,500	1,100	1,500	250°	Needle Roller	__	00000000	000000	0000000	00000
Steel Flat Rollers without Seal
16	11	6	16	M6	1	8	12	0.6	7,000	1,900	1,500	245°	Needle Roller	Mounting Hardware	0000000	00000	0000000	00000
19	11	8	20	M8	1.25	10	14	0.6	5,000	2,500	1,800	245°	Needle Roller	Mounting Hardware	0000000	00000	0000000	00000
Steel Flat Rollers with Seal
16	11	6	16	M6	1	8	12	0.6	7,000	1,900	1,500	175°	Needle Roller	Mounting Hardware	0000000	00000	0000000	00000
19	11	8	20	M8	1.25	10	13	0.6	5,000	2,500	1,800	175°	Needle Roller	Mounting Hardware	0000000	00000	0000000	00000

Maintenance-Free Threaded Track Rollers

Because they never need to be relubricated, these rollers are a good choice for hard-to-reach places. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. Some rollers have end seals to block dirt and contamination.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Track lubricators reduce friction and wear without shutting down equipment. Oil-infused resin distributes lubricant onto rollers, which transfer it to your track.

For technical drawings and 3-D models, click on a part number.

Metric

Track Rollers
Roller, mm		Stud, mm		Thread					Radial Load Cap., lbs.							Roller-Mount Track Lubricators
Dia.	Wd.	Dia.	Lg.	Size	Pitch, mm	Lg., mm	Shoulder Lg., mm	Max. Speed, rpm	Static	Dynamic	Max. Temp., °F	Bearing Type	Includes		Each		Each
Steel Crowned Rollers with Seal
16	11	6	16	M6	1	8	0.6	1,600	820	800	175°	Needle Roller	Mounting Hardware	000000	000000	0000000	000000
19	11	8	20	M8	1.25	10	0.6	1,200	1,000	950	175°	Needle Roller	Mounting Hardware	000000	000000	0000000	00000

Threaded Track Rollers with Adjustable Shoulder

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Secure the stud with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

For technical drawings and 3-D models, click on a part number.

Metric

Roller, mm		Stud, mm		Thread			Shoulder, mm				Radial Load Cap., lbs.
Dia.	Wd.	Dia.	Lg.	Size	Pitch, mm	Lg., mm	Dia.	Lg.	Ht. Adjustment Capability, mm	Max. Speed, rpm	Static	Dynamic	Max. Temp., °F	Bearing Type	Includes		Each
Steel Flat Rollers with Seal
16	11	6	16	M6	1	9	9	7	0.5	13,000	520	1,300	250°	Needle Roller	Mounting Hardware	0000000	0000000
19	11	8	20	M8	1.25	11	11	9	0.5	10,000	1,100	1,500	250°	Needle Roller	Mounting Hardware	0000000	000000
Steel Crowned Rollers with Seal
16	11	6	16	M6	1	9	9	7	0.5	13,000	520	1,300	250°	Needle Roller	Mounting Hardware	0000000	000000
19	11	8	20	M8	1.25	11	11	9	0.5	10,000	1,100	1,500	250°	Needle Roller	Mounting Hardware	0000000	000000

Shaft-Mount Track Rollers

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Lubricate rollers through a hole and groove in the inner ring.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Rollers with seal have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Metric

Roller, mm					Radial Load Cap., lbs.
Dia.	Wd.	For Shaft Dia., mm	Overall Wd., mm	Max. Speed, rpm	Static	Dynamic	Max. Temp., °F	Bearing Type	ID	ID Tolerance		Each
Black-Oxide Steel Crowned Rollers with Seal
16	11	5	12	14,000	750	700	210°	Needle Roller	5mm	-0.008mm to 0mm	0000000	000000
19	11	6	12	11,000	900	750	210°	Needle Roller	6mm	-0.008mm to 0mm	0000000	00000

Tapered Stud Track Rollers

Roller

Grease Fitting

Install these rollers in worn-out mounting holes or where you don’t have access to the back of the mounting hole. The stud is tapered, so you can quickly secure them in place with a set screw (not included) instead of a nut on the back like traditional rollers. Keep in mind, this reduces their radial capacity.

Rollers with a seal protect rolling elements from dirt and contamination better than shielded rollers, but they do hold more heat. The seal also helps retain lubrication.

Add a grease fitting to create a lubrication point.

For technical drawings and 3-D models, click on a part number.

Track Rollers
Roller, mm		Stud, mm		Shoulder, mm			Radial Load Cap., lbs.						Grease Fittings
Dia.	Wd.	Dia.	Lg.	Dia.	Lg.	Max. Speed, rpm	Static	Dynamic	Max. Temp., °F	Bearing Type		Each		Each
Steel Flat Rollers with Seal
16	11	6	20	12	0.6	17,500	800	800	175°	Needle Roller	0000000	000000	0000000	00000
19	11	8	20	15	0.6	14,000	1,000	930	175°	Needle Roller	0000000	00000	0000000	0000

Threaded V-Groove Track Rollers

External Hex Shoulder Drive

Thread the stud directly into a component or secure with a nut for through-hole mounting. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Also known as cam followers, track rollers support loads while guiding and positioning work. All rollers are permanently lubricated.

440C stainless steel rollers offer better corrosion resistance than steel rollers.

Rollers with a plastic overmold make less than noise than other rollers, and they’re suitable for corrosive environments. However, they have lower weight capacities than other similarly sized rollers and they’re less corrosion resistant than other stainless steel rollers.

Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.

For technical drawings and 3-D models, click on a part number.

External Hex Shoulder Drive—Metric

Roller, mm		Stud, mm		Thread					Groove, mm			Radial Load Cap., lbs.
Dia.	Wd.	Dia.	Lg.	Size	Pitch, mm	Lg., mm	Shoulder Lg., mm	Hex Shoulder Wd., mm	Wd.	Dp.	Max. Speed, rpm	Static	Dynamic	Static Thrust Load Cap., lbs.	Max. Temp., °F	Bearing Type	Features	Includes		Each
440C Stainless Steel V-Groove Rollers with Seal
31	11	10	25	M10	1.5	15	2.6	14	6	3	3,400	490	450	110	500°	Ball	__	Mounting Hardware	0000000	0000000
31	11	10	25	M10	1.5	15	2.6	14	6	3	3,400	590	590	140	210°	Ball	__	Mounting Hardware	0000000	000000
Steel V-Groove Rollers with Seal
31	11	10	11	M10	1.5	11	4.1	14.29	6	3	3,400	590	590	140	245°	Ball	__	__	0000000	00000
31	11	10	25	M10	1.5	15	2.6	14	6	3	3,400	590	590	140	210°	Ball	__	Mounting Hardware	0000000	00000
Steel V-Groove Rollers without Seal
31	11	10	11	M10	1.5	11	4	14	5	3	620	16	16	9	245°	Ball	Plastic Overmold, Shielded	__	0000000	00000

Threaded V-Groove Track Rollers with Adjustable Shoulder

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. Secure the stud with a nut for through-hole mounting. All rollers are permanently lubricated.

440C stainless steel rollers offer better corrosion resistance than steel rollers.

Rollers with a plastic overmold make less noise than other rollers, and they’re suitable for corrosive environments. However, they have lower weight capacities than other similarly sized rollers and they’re less corrosion resistant than other stainless steel rollers.

Rollers with a seal block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seal also helps retain lubricant.

For technical drawings and 3-D models, click on a part number.

External Hex Shoulder Drive—Metric

Roller, mm		Stud, mm		Thread					Groove, mm			Radial Load Cap., lbs.
Dia.	Wd.	Dia.	Lg.	Size	Pitch, mm	Lg., mm	Shoulder Lg., mm	Hex Shoulder Wd., mm	Wd.	Dp.	Max. Speed, rpm	Static	Dynamic	Static Thrust Load Cap., lbs.	Max. Temp., °F	Features	Includes		Each
Steel V-Groove Rollers with Seal
31	11	10	11	M8	1.25	9	4.1	14.29	6	3	3,400	590	590	140	245°	__	Mounting Hardware	0000000	000000
31	11	10	25	M10	1.5	15	2.6	14	10	3	3,400	590	590	140	210°	__	Mounting Hardware	0000000	00000
440C Stainless Steel V-Groove Rollers without Seal
31	11	10	11	M8	1.25	8	4	14	6	3	620	16	16	9	245°	Plastic Overmold, Shielded	__	0000000	00000

Sanitary Threaded V-Groove Track Rollers

Guide loads along angle rail tracks in food and pharmaceutical plants or other sanitary environments with these threaded rollers. They’re permanently lubricated, a feature often seen in sanitary areas where repeated lubrication could cause contamination. Their lubricant is NSF registered H1 as safe for incidental contact with food. They’re made of stainless steel, so they won’t corrode from frequent washdowns with harsh cleaners. The bearings are sealed and shielded to keep out liquid and make sure the lubricant stays intact. These rollers have a V-groove profile, which allows debris to fall off when they’re mounted on angle rails. They’re also known as cam followers.

Rollers with a standard shoulder have a threaded mounting stud. Thread them directly into a component, or secure them with a nut for through-hole mounting.

Rollers with an adjustable shoulder are also known as eccentric track rollers. They can be moved up and down, and they’re commonly used alongside standard rollers to correct misalignment. Secure them with a nut for through-hole mounting.

For technical drawings and 3-D models, click on a part number.

Roller, mm		Stud, mm		Thread						Groove, mm			Radial Load Cap., lbs.
Dia.	Wd.	Dia.	Lg.	Size	Pitch, mm	Lg., mm	Shoulder Lg., mm	Hex Shoulder Wd., mm	Ht. Adjustment Capability, mm	Wd.	Dp.	Max. Speed, rpm	Static	Dynamic	Static Thrust Load Cap., lbs.	Max. Temp., °F	Bearing Type	Includes		Each
Single-Sealed 440C Stainless Steel V-Groove Rollers
Standard Shoulder
31	11	10	25	M10	1.5	15	3.1	14	1	6	3	3,400	590	590	140	175°	Ball	Mounting Hardware	0000000	0000000
Adjustable Shoulder
31	11	10	25	M10	1.5	15	3.1	14	1	6	3	3,400	590	590	140	175°	Ball	Mounting Hardware	0000000	000000