We will reply to your message within an hour.
More
18-8 stainless steel screws have good chemical resistance.
More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.
Stronger and more wear resistant than 18-8 and 316 stainless steel, these screws are mildly chemical resistant.
These steel screws are available with corrosion-resistant finishes.
One-third the weight of steel, aluminum screws resist corrosion in wet environments.
Brass screws are corrosion resistant in wet environments and electrically conductive.
These steel screws are zinc plated to resist corrosion in wet environments.
Made from 18-8 stainless steel, these screws are chemical resistant.
A Torx drive has more points of contact than Phillips, slotted, and square drives, allowing you to apply extra force with less slippage or damage to the recess.
A thick, decorative head provides a finished appearance.
A free-rotating, permanently attached washer distributes holding pressure over a wider area than a flange and remains stationary to prevent scratching the material surface as you tighten the screw.
A tamper-resistant Torx driver is required for installation and removal. Also known as pin-in-Torx, these screws allow you to apply extra force with less slippage or damage to the recess.
The S-shaped drive can be installed with a standard slotted driver, but requires a special tool for removal.
These screws require a Tri-Wing® driver for installation and removal.
Install and remove these screws with a tamper-resistant spanner driver.
Also known as pin-in-hex, install and remove these screws with a tamper-resistant hex driver.
A flange under the head distributes holding pressure and reduces the risk of crushing thin metal.
These square-drive screws have a flange under the head that distributes holding pressure and reduce the risk of crushing thin metal.
These steel screws have a black-oxide finish to resist corrosion in dry environments.
Stronger and more wear resistant than 316 and 18-8 stainless steel, these screws are mildly chemical resistant.
Also known as Fastite screws, these offer more thread engagement in 0.028" to 0.063" thick sheets to prevent overtightening and damaging threads.
Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.
For a finished appearance that reduces the chance of snags on other material, these screws fit snugly in countersunk holes and have a domed head.
A wide cutting slot provides excellent chip clearing and low driving torque in soft metal.
These metric screws have a triangular shank that presses tightly as it forms threads, so screws resist loosening in soft metals such as brass, aluminum, and copper.
The triangular shank presses tightly as it forms threads, so screws resist loosening in soft metals such as brass, aluminum, and copper.
Also known as Swageform screws, threads at the tip are designed to grab material for a fast start with low torque in a wide range of materials.
Drill a pilot hole, cut threads, and fasten in one motion with these metric-threaded screws. Made of steel, they’re strong and wear resistant.
Stronger and more wear resistant than 18-8 stainless steel, these screws are mildly chemical resistant.
By drilling their own holes and fastening in a single operation, these square-drive screws save time and effort. Made of 410 stainless steel, they're both stronger and more wear resistant than 18-8 stainless steel screws.
The extra-wide truss head distributes holding pressure to reduce the risk of crushing thin metal.
Also known as pancake head screws, these have a head that is about two-thirds the height of standard rounded head screws.
A decorative rounded top provides a finished appearance.
These screws have a free-rotating, permanently attached washer that remains stationary while tightening to prevent bunching while attaching tarps and other fabric to metal.
Also known as roofing screws, these screws are long and made from hardened steel to fasten rigid insulation board to steel decking.
Made from stainless steel to resist galvanic corrosion, use these screws to fasten aluminum to aluminum and steel framing. They save you time and effort by drilling their own holes and fastening in a single operation.
These 18-8 stainless steel screws have good chemical resistance.
These steel screws have a black-oxide or zinc-plated finish to resist corrosion.
Stronger and more wear resistant than 18-8 stainless steel screws, these are mildly chemical resistant.
These steel screws have alternating high and low threads to minimize cracking and splitting in brittle material such as phenolic and glass-filled plastic.
These screws cut threads into drilled holes as they’re turned, so they require less driving torque and cause less stress on material than thread-forming screws.
A point centers the screw in a starter hole and widely spaced threads reduce the risk of cracking plastic.
These Phillips head screws have a decorative rounded top that provides a finished appearance.
With a low-profile rounded head that’s flanged to sit flush for a finished appearance, these screws press threads into wood on cabinets, trim, molding, and light duty framing.
Fasten sheet metal up to 0.200" thick.