Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Hold pipe, tubing, and conduit away from strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Support vertical pipes passing through floors.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Cut as much strap as you need to hang duct, pipe, and other materials.

A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Also known as blank eyebolts, you can weld or thread these to suit your application.

Use these eyebolts for routing wire and for other light duty applications.

Also known as thimble eyebolts, the large, contoured groove in the eye reduces kinks and minimizes the wear on your wire rope.

Also known as nut eyebolts, these are designed for through-hole applications.

Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.

The spring-loaded latches on these hooks snap back into place, securing your load.

These hooks have closed ends on both sides.

These hooks meet MS-87006.

One side is closed and the other is open.

The pins have flush ends to prevent snagging and accidental disengagement.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

The strongest shackles we offer, these connectors have a pin with flush ends that prevents snagging and accidental disengagement.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

A lip on the shackle keeps the pin from falling out when loosened.

For use in low-vibration applications where the shackle remains stationary.

To prevent these shackles from snagging or accidentally coming undone, their pin doesn’t stick out from their body.

A lip on the shackle keeps the screw from falling out when loosened.

For use in low-vibration applications where the shackle remains stationary.

The bolt on these shackles is fastened with a nut and cotter pin, making them more secure than shackles with a screw pin. Also known as D-shackles, they have a narrow opening that restricts the movement of wire rope and chain.

The pin doesn’t stick out from their body, so these shackles won’t snag or accidentally come undone. They have a narrow opening that restricts the movement of wire rope and chain.

A lip on the shackle keeps the pin from falling out when loosened.

The twisted shape of these shackles keeps rope and chain from twisting and knotting. And if their screw becomes loose, the lip on the shackles prevents it from falling out.

Attach a rope to the ring on the pin for remote release where access in limited. These shackles have an eye end for connecting to a hook.

Disconnect by pulling the lever or attach rope to the eye on the lever for remote release.