Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

These carriages and guide rails are steel.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

Designed for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

Mount to vertical surfaces for applications where tight tolerances aren't required.

These track roller carriages and guide rails are stainless steel for use in wet, corrosive environments.

Use these carriages and guide rails for light loads where precise movement is not required.

A handle on the side of the carriage locks the carriage in place.

Combine with a T-slotted rail to add linear motion to your assembly.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

A handle on the side of the carriage locks the carriage in place.

A handle locks these carriages in place on curved paths, loops, and circuits in assembly stations and other repetitive processes.

These steel track rollers and guide rails support loads up to 300 lbs.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

With two bearings mounted in a single housing, these bearings have higher load capacities than standard ones. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.

With two bearings mounted in one housing, these sleeve bearings withstand heavy loads. Use them on round support rail shafts for applications that require maximum rigidity.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

The flanged housing makes these bearings a good solution for vertical linear motion applications.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Float bearings on air for precise, frictionless movement. Unlike traditional bearings that can wear your shaft down, these bearings are suspended using pressurized air for linear and rotary motion.

Use the adjustment screw in the housing to tighten or loosen the snugness (also known as preload) of the bearing to your shaft.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Made from a single piece of slippery UHMW plastic, these bearings have no cracks or crevices so they’re easy to clean.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

Modify the stroke length on these air slides to meet changing application requirements—slides have adjustable shaft collars on the guide rods that you can move to fine-tune the stroke length.

With PTFE sleeve bearings and a low-friction ball screw, these slides don’t require the mess and maintenance of lubrication but still give you precise positioning anywhere along the length of their stroke.