These discs have multiple layers of brick-shaped abrasive arranged in a pattern to create highly consistent finishes.

Coated with either ceramic alumina or a premium form of aluminum oxide, these discs last longer, cut faster, and produce a more consistent finish than standard hook and loop discs.

These discs have a harder abrasive than standard quick-change discs.

The heavy duty construction provides more support than standard discs for heavy material removal.

These discs have a harder abrasive than standard flexible-edge quick-change discs.

The premium abrasive stays sharp longer.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a long-lasting diamond abrasive.

A coating prevents dust and debris from building up on the abrasive surface.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

For use with vacuum sanders, these discs have holes that allow dust to get sucked up before it can build up and dull the abrasive surface.

Coated with diamond grit, use these discs for sanding hard nonmetals.

Change your discs less often—the zirconia alumina grit on these discs continually fractures to produce new, sharp cutting edges.

Holes in the disc let you see the surface you’re sanding.

The ceramic alumina abrasive on these discs is sharp and dense enough to shape hard metals such as stainless steel, nickel, and cast iron without dulling quickly.

The premium abrasive stays sharp longer. Holes in the disc let you see the surface you’re sanding.

Overlapping abrasive flaps bonded to a backing plate provide consistent material removal and even finishes.

These discs have a harder abrasive than standard flap sanding discs.

The flaps alternate between an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

These discs have 30% more flaps than standard flap sanding discs to last longer.

These discs have a harder abrasive than standard flap sanding discs for corners.

With more flaps than standard discs, these last 30-40% longer.

Replace your sanding discs less often—the backing plate on these discs can be trimmed off as the abrasive flaps wear down, allowing you to use more of the disc.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

A coating prevents dust and debris from building up on the abrasive surface.

The zirconia alumina grit on these discs continually fractures to produce new, sharp cutting edges that aggressively remove material from steel and wood.

The ceramic alumina abrasive on these discs is sharp and dense enough to shape hard metals such as stainless steel, nickel, and cast iron without dulling quickly.

Coated with aluminum oxide—the most common abrasive material, hard enough to sand steel and wood.

Create smooth finishes on wood with these garnet sheets.

These rolls are coated with aluminum oxide, which is the most common abrasive material and hard enough to sand steel and wood.

These sheets resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

Providing the control of a sanding block while remaining flexible, these sponges sand around curves and in corners.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding. A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block. They have a long-lasting diamond abrasive on one side.

The sharp abrasive on these rolls sands hard metals like stainless steel, nickel, and iron.

Cut the length you need, then quickly attach, remove, and reuse.

Holes allow dust removal when used with a vacuum sander to prevent buildup of debris on the abrasive surface.

Cut to convenient sizes and shapes, these fit most sheet sanders.

Sharper than silicon carbide and harder than ceramic alumina, the diamond abrasive on these sheets is ideal for sanding concrete, fiberglass, and other tough materials.

Peel and stick to your file handle. When it’s time to change the sheet, peel it off.

A coating prevents dust and debris from building up on the abrasive surface.

Quickly switch between different grits—these sanding sheets attach and detach from a compatible sanding block with hook and loop.

Also known as abrasive wraps, these sheets are cut to fit around the drum of a drum sander.

The ceramic alumina abrasive on these pads is sharp and dense enough to shape hard metals such as stainless steel, nickel, and iron without dulling quickly.

Avoid clogs when you're removing paint or rust. The widely spaced grains on these belts give dust and debris a place to collect so they won't build up on the surface.

These belts resist deterioration when used with water or cutting fluids.

Dense and hard, the ceramic alumina abrasive on these belts removes material faster and lasts longer than standard aluminum oxide abrasives.

Use these narrow belts on hand-held sanding sticks.