We will reply to your message within an hour.
More
Press onto a compatible sanding tool or backup pad; peel off to remove.
A coating prevents dust and debris from building up on the abrasive surface.
The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.
Holes allow dust removal when used with a vacuum sander.
The premium abrasive stays sharp longer.
These discs have a long-lasting diamond abrasive.
A special fastener on the back of these discs allows you to easily swap one disc for another.
These discs have a harder abrasive than standard quick-change discs.
The heavy duty construction provides more support than standard discs for heavy material removal.
These discs have a harder abrasive than standard flexible-edge quick-change discs.
The outer 3/8" of these discs is extremely flexible to prevent marring or gouging your work when sanding a radius or contour.
The abrasive-embedded nylon mesh construction gives you more control over sanding pressure.
Thicker, more pliable, and less aggressive than standard nylon mesh quick-change discs, use these for finer sanding on curved surfaces.
Debur, clean, and blend faster than other nylon mesh discs.
Used for heavy cleaning and stripping, these discs have an abrasive-embedded nylon mesh construction that gives you more control over sanding pressure.
The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.
The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.
Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.
The thick, abrasive-embedded nylon mesh construction gives you maximum control over sanding pressure.
These discs are abrasive-embedded cloth with a cushioned layer.
Made of foam, these discs can conform to contoured shapes, corners, and sharp edges.
Fit these discs over your tool's arbor.
Holes in the disc let you see the surface you’re sanding.
The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.
Fit these discs over your tool’s arbor to sand stainless steel and hard metals.
The premium abrasive stays sharp longer. Holes in the disc let you see the surface you’re sanding.
Used for stripping, these discs eliminate discoloration from heat buildup.
Fit these discs over your tool's arbor to sand aluminum, soft metals, and nonmetals.
Fit these discs over your tool's arbor to sand masonry, ceramics, and composites.
Secure the shank into the collet or chuck of your tool.
With more flaps than standard discs, these last 30-40% longer.
These discs have a harder abrasive than standard flap sanding discs.
The flaps have an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.
The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.
Set at an angle and widely spaced, the flaps reach into corners.
The flaps wrap around the outer edge of these discs to sand welds at right angles.
Overlapping abrasive flaps bonded to a backing plate provide consistent material removal and even finishes.
The abrasive-embedded mesh construction gives you more control over sanding pressure, creating more consistent finishes.
A heavy duty backing plate provides more support than standard discs for heavy material removal.
The flaps alternate between an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.
Set at an angle and widely spaced, the overlapping abrasive flaps reach into corners.
These discs have a harder abrasive than standard flap sanding discs for corners.
Use with commercial floor buffing machines to sand wood floors and strip tape from concrete.
Use these discs with commercial floor buffing machines to sand wood floors.
Secure the shank into the collet or chuck of your tool. Attach the quick-change fastener on the sanding disc to the corresponding fastener on the backup pad.
The flexible edge of the sanding disc overhangs these backup pads.
Thread these pads onto the tool’s arbor.
Thread the stud into the tool's spindle.
Use screws to attach these pads to a tool.
Secure the shank into the collet or chuck of a tool.
Mount one of these pads onto the tool's arbor.
These pads are designed to channel air flow to the sanding disc for cooler operation, prolonging the life of the disc.
Designed to rotate independently of the disc, these pads clear material buildup on the abrasive surface for longer disc life.
Thread one of these backup pads onto the tool’s arbor, then attach a sanding disc and secure with the disc nut.
Holes in the pad align with holes in the sanding disc for a clearer view of the sanding surface.
Thread the stud into the tool's spindle and then press the sanding disc onto the backup pad.
Swap between hook-and-loop and adhesive-backed sanding discs on one sander. Rather than replace your entire sanding pad, mount these adapters to create a hook-and-loop or adhesive-backed attachment.
Convert your threaded grinder spindle into a 5/8"-11 size that's compatible with common grinding wheels and sanding discs.