Keep sanding sheets of various grits on hand.

The grit particles are block shaped and cut slowly to produce a polished surface on metals.

These rolls are coated with aluminum oxide, which is the most common abrasive material and hard enough to sand steel and wood.

A thicker, heavier construction than standard rolls withstands tough sanding.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

The dental floss of abrasives, these cords slip into areas that other forms cannot. They're good for deburring and polishing small holes, narrow slots, keyways, and grooves.

These rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

Keep a variety of grits on hand, so you always have the right one for the job. These sheets won’t deteriorate when used wet or with grease, chemicals, cutting fluids, and other solvents.

A coating prevents dust and debris from building up on the abrasive surface.

A cushioned layer lets you apply more even sanding pressure on your workpiece, creating finer and more consistent finishes.

The mesh in these sanding pads flexes to compensate for uneven pressure as you sand, producing a consistent finish.

When you need to achieve a more consistent finish, choose nylon mesh sanding rolls over paper- or cloth-backed rolls.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.

Keep a selection of flat and angled sponges with various grits on hand.

Evenly sand two surfaces at once.

Peel and stick to your sanding tool. When it’s time to change the sheet, peel it off.

Use these rolls to create consistent finishes on hard metals such as stainless steel, iron, and nickel.

Quickly attach, remove, and reuse.

Holes allow dust removal when used with a vacuum sander to prevent buildup of debris on the abrasive surface.

Peel and stick these sheets to your detail sander whenever it’s time for fresh grit.

Stick these sheets to your dust-collecting detail sander to smooth edges, corners, and other tight spaces.

A coating prevents dust and debris from building up on the abrasive surface.

Quickly switch between different grits—these sanding sheets attach and detach from a compatible sanding block with hook and loop.

A coating prevents dust and debris from building up on the abrasive surface.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

Holes allow dust removal when used with a vacuum sander.

The ceramic alumina abrasive on these discs is sharp and dense enough to shape hard metals such as stainless steel, nickel, and cast iron without dulling quickly.

For use with vacuum sanders, these discs have holes that allow dust to get sucked up before it can build up and dull the abrasive surface.

Coated with either ceramic alumina or a premium form of aluminum oxide, these discs last longer, cut faster, and produce a more consistent finish than standard hook and loop discs.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

Thicker, more flexible, and less aggressive than standard nylon mesh discs, use these for sanding on curved or delicate surfaces.

These discs are abrasive-embedded cloth with a cushioned layer.

When you need to achieve a more consistent finish, choose nylon mesh sanding discs over paper- or cloth-backed discs.

The premium abrasive stays sharp longer.

The heavy duty construction provides more support than standard discs for heavy material removal.

These discs have a harder abrasive than standard flexible-edge quick-change discs.

Get twice the life over standard nylon mesh cushioned discs—the flexible mesh in these discs is embedded with a premium form of aluminum oxide or ceramic alumina.

The nylon mesh on these discs is embedded with precision-shaped ceramic alumina, which cuts through hard metals like stainless steel faster than other forms of ceramic alumina because of its sharp, outwardly pointed grit.

The premium abrasive stays sharp longer.

When you need to achieve a more consistent finish, choose nylon mesh sanding discs over paper- or cloth-backed discs.

Change your discs less often—the zirconia alumina grit on these discs continually fractures to produce new, sharp cutting edges.

A coating prevents dust and debris from building up on the abrasive surface.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Nylon mesh is embedded with precision-shaped ceramic alumina, which cuts through hard metals like stainless steel faster than other forms of ceramic alumina because of its sharp, outwardly pointed grit.

The premium abrasive stays sharp longer.

The ceramic alumina abrasive on these discs is sharp and dense enough to shape hard metals such as stainless steel, nickel, and cast iron without dulling quickly.

The premium abrasive stays sharp longer. Holes in the disc let you see the surface you’re sanding.

Prepare material surfaces for finishing processes such as coating, painting, and soldering—these discs contain an extra coarse ceramic alumina abrasive for heavy cleaning and stripping of stainless steel, nickel, and other hard metals.

Overlapping abrasive flaps bonded to a backing plate provide consistent material removal and even finishes.

These discs have a harder abrasive than standard flap sanding discs.

A heavy duty backing plate provides more support than standard discs for heavy material removal.

These discs have 30% more flaps than standard flap sanding discs to last longer.

These discs have a harder abrasive than standard flap sanding discs for corners.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

With more flaps than standard discs, these last 30-40% longer.

Replace your sanding discs less often—the backing plate on these discs can be trimmed off as the abrasive flaps wear down, allowing you to use more of the disc.

The flaps wrap around the outer edge of these discs to sand welds at right angles.