Aluminum Scaffold Planks
Aluminum is a good choice for damp areas and outdoor use. Hooks with a 2" opening at each end secure planks to end frames. Rungs on the underside are for use as hand grips. Planks have a perforated surface for slip resistance and to reduce debris buildup. End hooks are offset to allow for continuous planking of large scaffolds.
Note: Length is measured from center-to-center of end hooks.
Note: Planks meet OSHA and Cal/OSHA dimensional and construction standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe set-up and operating practices.
Rail | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg., ft. | Wd. | Ht. | Cap., lbs. | Plank Tread | Ht. | Material | Wt., lbs. | Assembled or Unassembled | Features | Specifications Met | Each | |
| 10 | 19 1/16" | 4" | 250 | Perforated | 4" | Aluminum | 43 | Unassembled | 2" End Hooks | ANSI/ASSP A10.8, OSHA Compliant 29 CFR 1926.451, Cal/OSHA Compliant Title 8 Section 1637, UL 1322 | 0000000 | 0000000 |
Plywood Scaffold Planks
The most commonly used and cost-effective planking for scaffolding walkways. Install three of these planks side-by-side to create a full platform atop standard 5 ft. wide scaffold frames. Hooks with a 2" opening at each end secure these planks to end frames. Their plywood walking surface can be replaced with standard 5/8" thick plywood when worn.
Note: Length is measured from center-to-center of end hooks.
Note: Planks meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices.
Rail | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg., ft. | Wd. | Ht. | Cap., lbs. | Plank Tread | Ht. | Material | Wt., lbs. | Assembled or Unassembled | Features | Specifications Met | Each | |
| 10 | 19" | 4" | 1,000 | Smooth | 4" | Aluminum | 46 | Assembled | 2" End Hooks | ANSI/ASSP A10.8, OSHA Compliant 29 CFR 1926.451, Cal/OSHA Compliant Title 8 Section 1637, Cal/OSHA Compliant Title 8 Section 1646 | 0000000 | 0000000 |
Plywood Scaffold Planks with Access Door
Safely climb inside your scaffold when surrounding space is tight. These planks have an access door that swings open to reach your work platform. They’re made of plywood—the most commonly used and cost-effective planking material for scaffolds. Hooks at each end secure these planks to end frames. Length is measured from center-to-center of the end hooks.
Use an additional plank (sold separately) to create a platform that spans a standard 5 ft. wide scaffold. They do not include an access door.
Note: Planks meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.
Planks with Access Door | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Rail | Additional Planks | |||||||||||||
| Lg., ft. | Wd. | Ht. | Cap., lbs. | Plank Tread | Ht. | Material | Wt., lbs. | Assembled or Unassembled | Features | Specifications Met | Each | Each | ||
| 10 | 28" | 4 1/2" | 1,100 | Smooth | 4 1/2" | Aluminum | 55 | Assembled | 2" End Hooks, Access Door | Cal/OSHA Compliant Title 8 Section 1637, Cal/OSHA Compliant Title 8 Section 1646, Cal/OSHA Compliant Title 8 Section 3622, OSHA Compliant 29 CFR 1926.451, ANSI/ASSP A10.8 | 0000000 | 0000000 | 0000000 | 0000000 |
Scaffold Guardrails
Add a barrier around your scaffold platform to prevent falls. These guardrails attach to posts (not included) on the edge of your platform. You can also replace sections of an existing barrier to make sure your scaffold meets safety requirements. Made of galvanized steel, these guardrails resist rust and hold up to outdoor use.
Note: Guardrails meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.
Mounting | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Lg., ft. | OD | Material | Wt., lbs. | Hardware Included | No. of Holes | Hole Dia. | Specifications Met | Each | |
Side Rails | |||||||||
| 10 | 1 1/4" | Galvanized Steel | 9 | No | 2 | 9/16" | Cal/OSHA Compliant Title 8 Section 1646, OSHA Compliant 29 CFR 1910.29, OSHA Compliant 29 CFR 1926.451 | 0000000 | 000000 |