Planks, Guardrails, and Toeboards
Create catwalks, bridges, gangways, and mezzanines by combining these planks, guardrails, and toeboards. They also work well between trestles, ladder jacks, and ladder scaffolding supports. Rungs on the underside are for use as hand grips.
Planks have a slip-resistant surface for sure footing. The vinyl end caps protect against sharp edges and act as hand grips.
Note: Planks, guardrails, and toeboards meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices. Planks, guardrails, and toeboards also meet CAL-OSHA standards, which is required for use in California.
500-lb. Capacity | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Lg., ft. | Ht. | Wt., lbs. | Material | Plank Tread | Mounting Hardware Included | Assembled or Unassembled | Specifications Met | Each | |
14" Wd. | |||||||||
| 8 | 4" | 27 | Aluminum | Smooth | Yes | Unassembled | ANSI/ASSP A10.8, Cal/OSHA Compliant Title 8 Section 1637, OSHA Compliant 29 CFR 1926.451, UL 1322 | 0000000 | 0000000 |
20" Wd. | |||||||||
| 8 | 4" | 33 | Aluminum | Smooth | Yes | Unassembled | ANSI/ASSP A10.8, Cal/OSHA Compliant Title 8 Section 1637, OSHA Compliant 29 CFR 1926.451, UL 1322 | 0000000 | 000000 |
24" Wd. | |||||||||
| 8 | 4" | 38 | Aluminum | Smooth | Yes | Unassembled | ANSI/ASSP A10.8, Cal/OSHA Compliant Title 8 Section 1637, OSHA Compliant 29 CFR 1926.451, UL 1322 | 0000000 | 000000 |
28" Wd. | |||||||||
| 8 | 4" | 41 | Aluminum | Smooth | Yes | Unassembled | ANSI/ASSP A10.8, Cal/OSHA Compliant Title 8 Section 1637, OSHA Compliant 29 CFR 1926.451, UL 1322 | 0000000 | 000000 |
Aluminum Scaffold Planks
Aluminum is a good choice for damp areas and outdoor use. Hooks with a 2" opening at each end secure planks to end frames. Rungs on the underside are for use as hand grips. Planks have a perforated surface for slip resistance and to reduce debris buildup. End hooks are offset to allow for continuous planking of large scaffolds.
Note: Length is measured from center-to-center of end hooks.
Note: Planks meet OSHA and Cal/OSHA dimensional and construction standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe set-up and operating practices.
Rail | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg., ft. | Wd. | Ht. | Cap., lbs. | Plank Tread | Ht. | Material | Wt., lbs. | Assembled or Unassembled | Features | Specifications Met | Each | |
| 8 | 19 1/16" | 4" | 250 | Perforated | 4" | Aluminum | 34 | Unassembled | 2" End Hooks | ANSI/ASSP A10.8, OSHA Compliant 29 CFR 1926.451, Cal/OSHA Compliant Title 8 Section 1637, UL 1322 | 0000000 | 0000000 |
Plywood Scaffold Planks
The most commonly used and cost-effective planking for scaffolding walkways. Install three of these planks side-by-side to create a full platform atop standard 5 ft. wide scaffold frames. Hooks with a 2" opening at each end secure these planks to end frames. Their plywood walking surface can be replaced with standard 5/8" thick plywood when worn.
Note: Length is measured from center-to-center of end hooks.
Note: Planks meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices.
Rail | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg., ft. | Wd. | Ht. | Cap., lbs. | Plank Tread | Ht. | Material | Wt., lbs. | Assembled or Unassembled | Features | Specifications Met | Each | |
| 8 | 19" | 4" | 750 | Smooth | 4" | Aluminum | 42 | Assembled | 2" End Hooks | ANSI/ASSP A10.8, OSHA Compliant 29 CFR 1926.451, Cal/OSHA Compliant Title 8 Section 1637, Cal/OSHA Compliant Title 8 Section 1646 | 0000000 | 0000000 |
Uneven Surface Scaffolds
Even if your surface isn't level, your scaffold can be—the end frames on these scaffolds adjust independently so you can set each side at a different height. You can change the plank height in 4" increments; use the spring-loaded pins to lock it in place.
Guardrail/toeboard kits are required by OSHA when add-on height sections are used.
Note: Scaffolds meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices. Scaffolds also meet CAL-OSHA standards, which is required for use in California.
Wheel | Stem | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Mount Ht. | Cap. per Caster, lbs. | Dia. | Lg. | Wheel/Tread Material | Caster Type | Each | |
| 5" | 1 1/8" | 6 1/4" | 250 | 5/8" | 2" | Rubber | Swivel with Brake | 0000000 | 000000 |
| Overall Lg., ft. | Guardrail Ht. | Toeboard Ht. | Material | Color | Assembled or Unassembled | Specifications Met | Each | |
| 8 | 40" | 4" | Powder-Coated Steel | Yellow | Unassembled | ANSI/ASSP A10.8, OSHA Compliant 29 CFR 1910.29, Cal/OSHA Compliant Title 8 Section 1646 | 0000000 | 0000000 |