Fold these scaffolds for easy transport and storage. Height adjusts in 12" increments. Tighten the back brace bolts to lock the plank in place. Planks are grit coated for good slip resistance.

You are responsible for adhering to local, state, and federal safety codes, including OSHA.

These scaffolds provide the space and height to complete elevated projects that most work platforms can't reach. Height adjusts in 2" increments. Powder-coated steel means these scaffolds can be used outdoors and in damp areas.

Note: Scaffolds meet OSHA dimensional standards and CAL-OSHA standards for use in California. Users are responsible for checking local, state, and federal codes, including OSHA, for safe operating practices.

Move these scaffolds between work areas without climbing down from the platform. They have a pair of motorized wheels that you control with a joystick. When you stop moving, the motor locks them to keep these scaffolds in place. The steel frame is durable enough to withstand heavy use, and it’s powder-coated to prevent rust. Holes every 2" let you adjust the platform to the height you need. To prevent slips, the walking surface is coated in grit. These scaffolds also have an access door, so you can climb down through the platform when you’re in tight spots.

Use a standard 20V battery (not included) to power the motor. It comes with adapters for most power tool battery packs.

Note: These scaffolds meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe operating practices. They’re designed to be driven on level surfaces, and don’t exceed the OSHA-required maximum speed of 1 foot per second. The enclosed guardrails meet fall-protection requirements.

Save space with a rolling scaffold that doubles as a workbench. These scaffolds can be used as a miter saw stand, a storage rack, a utility cart—or as scaffolding. Made of powder-coated steel, they're both rust resistant and durable for industrial use. Height adjusts in 2" increments.

Note: Scaffolds meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.

Made of fiberglass, these scaffolds are nonconductive, so they’re commonly used in substations, server rooms, and near electrical systems. They’re also lightweight and resist corrosion. When space is limited, use the plank’s access door to safely climb from the inside. The plank is grit-coated to prevent slipping. When not in use, they fold for compact storage.

Note: Scaffolds meet OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.

Create catwalks, bridges, gangways, and mezzanines by combining these planks, guardrails, and toeboards. They also work well between trestles, ladder jacks, and ladder scaffolding supports. Rungs on the underside are for use as hand grips.

Planks have a slip-resistant surface for sure footing. The vinyl end caps protect against sharp edges and act as hand grips.

Guardrails mount to either side of the plank with the upper rails 38" to 42" above the plank surface.

Toeboards mount to either side of the plank. They clamp to guardrail posts.

Note: Planks, guardrails, and toeboards meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices. Planks, guardrails, and toeboards also meet CAL-OSHA standards, which is required for use in California.

Aluminum is a good choice for damp areas and outdoor use. Hooks with a 2" opening at each end secure planks to end frames. Rungs on the underside are for use as hand grips. Planks have a perforated surface for slip resistance and to reduce debris buildup. End hooks are offset to allow for continuous planking of large scaffolds.

Note: Length is measured from center-to-center of end hooks.

Note: Planks meet OSHA and Cal/OSHA dimensional and construction standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe set-up and operating practices.

The most commonly used and cost-effective planking for scaffolding walkways. Install three of these planks side-by-side to create a full platform atop standard 5 ft. wide scaffold frames. Hooks with a 2" opening at each end secure these planks to end frames. Their plywood walking surface can be replaced with standard 5/8" thick plywood when worn.

Note: Length is measured from center-to-center of end hooks.

Note: Planks meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices.

Build tube-and-clamp scaffolding and attach supports, such as railings, to frame-style structures. Also known as knuckles. These clamps fit the most common scaffold tube sizes. Made of galvanized steel, they are rust resistant and hold up in outdoor applications.

Rigid clamps create a secure 90° connection between two tubes.

Swivel clamps pivot to connect tubes at any angle.

Note: Clamps meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.

With a tripod base and adjustable legs, these stands help you create a stable, level work platform on stairs, slopes, and uneven ground. Pair with scaffold planks or stages. A pair holds up to 600 lbs. The legs adjust in 1 1/2" increments, so you can set each one to the exact height you need. Rubber feet keep them from slipping on smooth surfaces. Made of aluminum, these stands are lightweight and corrosion resistant. When your work is done, fold them flat and store them, or use the handle to carry them to another job.

Note: Work platforms that have OSHA specifications listed meet dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.

Fasten coupling pins, base plates, guardrail posts, and other components to scaffold frames. They replace missing pins on your scaffold frame to help you comply with OSHA safety requirements. Made of galvanized steel, they resist rust and hold up to outdoor use.

Pig-tail pins have a curved arm that wraps around the frame. They’re also known as gravity pins. Toggle pins have a hinged arm that flips down against the frame to lock the pin in place. They’re also known as hinge pins.

Note: Pins meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.