We will reply to your message within an hour.
When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.
When working at heights, secure a lanyard to the ring on these tools to prevent drops. The ring rotates around the shaft so the driver turns freely.
These standard nutdrivers have a hollow shaft that provides clearance to remove nuts from long bolts.
Sets include an assortment of nutdrivers.
Sets include an assortment of drivers that are drilled all the way through the shaft and handle for turning nuts on any length of threaded rod. They have a magnet in the tip to hold nuts in place.
The shaft and handle are drilled all the way through for turning nuts on any length of threaded rod. These drivers have a magnet in the tip to hold nuts in place.
Press down on the handle’s collar to adjust the shaft length or remove and replace the shaft to change sizes. Sets include a handle and multiple shafts.
A magnet in the tip holds nuts in place.
The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet ASTM and IEC standards.
An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet ASTM and IEC standards.
Protect your stainless steel fasteners by using a stainless steel driver. If steel flakes off a standard tool and into the threads, it can lead to rust and contamination. These drivers eliminate that risk.
Made of aluminum-bronze that is FM approved, these drivers help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
A magnet or retaining ring holds the nut in place.
Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.
The toughest bits available, these withstand the shock and twisting force of impact drivers. A magnet holds the nut in place.
Turn hex nuts and cap screws.
Assortments contain bits with multiple drive styles.
A magnet holds the nut in place.
These bits are also known as nut setters.
Turn fasteners from either end and reach into tight spots.
Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.
These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.
When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.
When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a bright gold-plated finish that makes them easy to see and less likely to be misplaced.
With a simple loop handle, these keys are the economical choice. They have a long shaft for reaching into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.
An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.
Start and initially turn nuts. These tools are not intended for final tightening or removal of fasteners.
Create your own tool by attaching these shafts to a handle, or use with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.
Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.
Extra-long bits allow access to hard-to-reach fasteners.
Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
These short sockets fit spaces where height clearance is limited.
Pivot the head to access fasteners from an angle.
Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.
Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.
Quickly position these sockets on square and external 8-point fasteners.
Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.
Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.
The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.
Achieve the best possible grip on hex fasteners and prevent rounding.
A magnet holds the fastener securely enough to drive self-tapping screws.
With a smaller OD than standard sockets, these fit between tightly spaced fasteners.
The 12-point shape quickly positions on hex fasteners.
Quickly position these sockets on square fasteners.
The hex shape grips hex fasteners and prevents rounding.
Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.
For high quality at a lower price, choose these U.S.A.-made sets.
Suitable for occasional maintenance work, these sets are imported.
Turn nuts on bolts and threaded rod, which pass through these sockets.
Make maximum contact on all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.
The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.
Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.
Change heads to use these tools as an open-end, box, square drive, or hex-key wrench.