Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

Made of alloy steel, these low-profile screws are nearly twice as strong as their stainless steel counterparts. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

Choose these metric screws for high-strength fastening. Often used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems, these screws are at least 25% stronger than medium-strength steel screws.

These metric screws help prevent counterclockwise-moving parts from loosening. Use them for medium-strength fastening.

Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

Designed for construction and exterior building applications, these metric screws are often used to join I-beams and scaffolding. Their partial threading leaves an unthreaded portion that is strong enough to stand up to the sideways forces of joints.

Choose these metric screws for high-stress applications, such as valves, pumps, motors, and automotive suspension systems. They are about 10% stronger than medium-strength steel screws. Their serrated flange helps to resist vibration.

More corrosion resistant than 18-8 stainless steel screws, these metric screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

Comparable to Class 12.9 steel.

With inch-sized threads the same diameter as the shoulder, these screws can handle heavy loads. They’re 18-8 stainless steel for good chemical resistance.

Also known as wheel and axle bolts, these metric screws have an unthreaded shoulder that acts as a shaft, so material attached to the threaded end can rotate.

These metric set screws have good chemical resistance.

These metric set screws have a tip that makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

These metric screws have a square head, so you can turn them by hand or use a wrench for more torque. Also known as half dog-point set screws, they have a protruding tip that locks within a mating hole or slot to keep parts aligned.

Made from alloy steel, these metric set screws have a pointed tip that wedges into the contact surface for a secure hold on soft materials such as brass.

Choose these metric bolts for fastening most machinery and equipment. They are twice as strong as low-strength steel bolts. Carriage bolts have a smooth, rounded head for a finished look. The square neck keeps these bolts from turning when tightening a nut.

Made of Grade B7 steel, the tensile strength of these threaded rods is one and a half times higher than low-strength steel threaded rods. They also meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.

These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

Fiberglass threaded rods are stronger than nylon threaded rods. They resist acids, solvents, salt water, and oil.

Install with a driver.

These spring plungers have a nose that is about three-times longer than standard long hex-nose spring plungers.

Lock the nose into the retracted position by pulling the handle and rotating it 90°.

Lock the nose into the retracted position by pulling the ring and rotating it 90°.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.

For quicker setups than a separate T-slot nut and stud, slide these bolts into T-slot tracks on machine tool tables.

Also known as nut eyebolts, these are designed for through-hole applications.

Route wire and cable through the smooth eye without snagging.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.