Create one action with these valves, such as extending a cylinder.

Because they require a key to operate, you can limit who is able to adjust these valves. They create one action, such as extending a cylinder.

The push buttons that operate these valves are separate from the logic unit, allowing you to position them away from machinery. Since both hands are required to simultaneously press the buttons, they protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create two actions, such as extending and then retracting a double-acting cylinder.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Also known as 4/3 closed-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Because they require a key to operate, you can limit who is able to adjust these valves. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 exhaust center valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 5/2 valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Control air-powered robot tools, such as pick-and-place grippers.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

In the off position, these valves stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They actuate by air signal, so they're good for environments where electrical use may be dangerous.

These valves create one action, such as extending a cylinder. Also known as 3/2 or pilot valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They activate when an object, such as a box rolling on a conveyor, pushes the actuator. Also known as 4-way and 5/2 valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 4-way and 5/2 valves.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.