Shaft Ends | McMaster-Carr

Filter by

System of Measurement

Shaft Diameter

0.235" to 0.500"

0.235" to 0.625"

0.235" to 0.750"

0.235" to 0.875"

Material

Stainless Steel

Tungsten Carbide

Shaft Type

Acme Lead Screw

Round with Support Rail

Construction

Shaft Mount Type

OD

ID

Overall Length

Thread Size

Shank Thread Size

Width

Mounted Bearing Type

Four-Bolt Flange Mount

Three-Bolt Flange Mount

Two-Bolt Flange Mount

Rod End Type

Ball Joint Linkage

RoHS

Compliant with Exemptions

REACH

DFARS Specialty Metals

Export Control Classification Number (ECCN)

Finish

Phosphate Coated

Shank Gender

For Shaft Misalignment Type

No Misalignment

Clamping Screw Material

Stainless Steel

Shank Center Length

Length

Keyway Width

Overall Width

How can we improve?

9,596 Products

Power Transmission

Machinable Shaft Ends

Machinable Shaft Ends

Mill custom pulleys, threaded hubs, sprockets, collars, and sensor targets and mount them to shafts

Shaft Couplings

Shaft Couplings

Connect two shafts to transfer rotary motion from one to the other

Shaft Adapters

Increase or reduce your shaft's diameter to fit equipment, or replace damaged shaft ends

U-Joints

Transfer torque between shafts at an angle; handle more torque and misalignment than flexible shafts

Shear Couplings

Shear Couplings

Sever the connection between shafts when there's too much torque to protect parts from breaking

Flexible Shafts

Flexible Shafts

Snake around curves and obstructions to transmit rotary motion along any path

Shaft Collars

Hold and position parts on a shaft, or limit shaft movement

Mounted Bearings

Mounted Bearings

Ball, roller, and sleeve bearings ready to bolt in place

Bearing Housings

Bearing Housings

Mount your own bearings in place

Bearing Nuts

Hold bearings, bushings, pulleys, and gears in place on threaded shafts and spindles

Bearing Adapter Sleeves

Bearing Adapter Sleeves

Close gaps between your bearing and shaft for a tight fit

Rod Ends

Use with connecting rods to support loads and control steering, tensioning, or pivoting motion

Rod End Nuts

Attach to rods, pipe, and tubing to make pivot and hinge points

Linear Shaft Supports

Linear Shaft Supports

Support linear shafts to prevent bending and rolling under loads

Rod End Inserts

Rod End Inserts

Attach to rod ends to increase the amount of misalignment they can handle

Rod End Seals

Keep dirt out and lubrication in to extend the life of rod ends

Clutches

Start and stop the transmission of power to machinery

Torque Limiters

Torque Limiters

Keep torque at or below a set limit to control tension or braking or protect machinery from overload

Clutch/Brakes

Control when to transmit power with a clutch and when to hold a load in place with a brake

Brakes

Control how much and how quickly your drive system slows down

Lead Screw Collars

Lead Screw Collars

Position components and limit travel along a lead screw

Building and Machinery Hardware

Ball Knobs

Provide grip on control levers and push-pull rods

Ball-Lever Shafts

Ball-Lever Shafts

Attach a ball knob to create a custom handle for operating machinery

Mechanical Control Cables

Mechanical Control Cables

Weave around obstructions to operate valves, throttles, and other machinery from a distance

Fluid Handling

Pipe and Pipe Fittings

Pipe and Pipe Fittings

Generally thicker and more rigid than tubing for distributing liquids and gases through your facility

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)