Slide the shaft in to install, then tighten to secure. For use with light to medium loads where shaft alignment is not critical, these shaft supports brace the end of a linear shaft along the ground or other flat surface.

Secure two linear motion shafts parallel to each other and the mounting surface to build a system that moves smoothly and doesn’t bind.

A removable collar allows access to the shaft without unbolting the flange. For use with light to medium loads where shaft alignment is not critical, these supports allow you to hold linear shafts perpendicular to the mounting surface. Secure the shaft by tightening the clamping screw.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

Use these UHMW bearings in wet, corrosive environments.

Made of acetal blended with PTFE, these bearings handle speeds twice as fast as standard sleeve bearings.

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface.

A strong steel housing allows these bearings to handle higher speeds than standard oil-embedded mounted sleeve bearings.

Ball bearings operate with less friction than other bearings, so they can run at higher speeds.

Also known as tapped-base bearings, these ball bearings mount to surfaces from the bottom through threaded holes. Because of their narrow profile, they’re commonly used in tight-clearance spaces, including systems where multiple shafts are mounted close together.

The lubricant in these mounted ball bearings is NSF registered H1 and FDA compliant for incidental contact with food.

Synthetic grease or graphite enables these bearings to operate in high temperatures.

These bearings have the highest speed ratings of any mounted ball bearing that we offer.

Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.

Made of FDA listed PEEK, these bearings are suitable for direct contact with food. The closed backing blocks out dust and other contaminants.

Capable of handling temperatures from -400° to 750° F, these graphalloy bearings have the widest temperature range of any of our mounted bearings.

Designed with a thin, compact housing, these bearings are good for space-constrained applications.

Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange.

Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting.

Use these bearings in corrosive environments and under water.

An elongated mounting hole on one side of the flange lets you adjust the position of these bearings without having to remove your shaft.

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange.

Use these bearings in corrosive environments and under water.

The tapered rollers in these bearings support large shafts at high static loads.

Rated IP69K for washdowns, these bearings stand up to frequent cleanings in food, beverage, pharmaceutical, and chemical plants.

Quickly mount bearings in these precision-flanged housings, no machining required.

Use one of these base-mount housings with your own bearing to create a custom mounted bearing.

Designed to handle heavy loads, these bearings have the highest load capacities of any mounted linear ball bearings we offer.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Made from a single piece of slippery UHMW plastic, these bearings have no cracks or crevices so they’re easy to clean.

With two bearings mounted in one housing, these sleeve bearings can handle heavier loads than standard mounted linear sleeve bearings.

Float bearings on air for precise, frictionless movement. Unlike traditional bearings that can wear your shaft down, these bearings are suspended using pressurized air for linear and rotary motion.

The shell, housing, and balls of these bearings are stainless steel for excellent corrosion resistance.

The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard mounted linear ball bearings for support rail shafts.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Pivots provide smooth motion at the junction between two T-slotted rails.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

A handle on the side of the carriage locks the carriage in place.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

The square profile prevents loads from twisting and rotating.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

A handle locks these carriages in place on curved paths, loops, and circuits in assembly stations and other repetitive processes.

Small enough to fit in a camera zoom lens and other precision motion applications, these carriages and guide rails have a black chrome-plated finish that diffuses light to prevent reflecting light from causing equipment to malfunction.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

For smooth, accurate movement around curves and loops, these carriages have ball bearings that work well in high-speed, high-load applications.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

These track roller carriages and guide rails are stainless steel for use in wet, corrosive environments.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

Combine with a T-slotted rail to add linear motion to your assembly.

A set of ball bearings reduces friction and secures the end of a ball or lead screw.

With no external moving parts, these air slides provide a long stroke, but have a static footprint—only the carriage on top moves.