These tools lock onto your material to prevent them from opening while bending and crimping.

Turn your impact driver into a power crimper, and create raised edges on sheet metal more quickly than hand crimpers.

Offset handles allow you to use these tools in tight spaces.

Create a raised edge in sheet metal that locks into the rolled edge of another piece.

Shape sheet metal using your bench vise as a sturdy base.

Position the movable forming dies, also known as fingers, to make boxes, trays, and pans in different widths.

Create long, uniform folds on the edges of sheet metal.

Also known as slip rolls, these curvers create bends, curves, and circles in sheet metal.

Make deep folds in roofing panels and other large pieces of sheet metal.

Open sheet metal seams without cutting. The jaws slide under seams to pry the sheets apart.

Create squares, coils, and S‐shapes.

Bend wire and rod up to 3/8" diameter and flat stock up to 1/2"×3/16".

For small projects, these wire benders form steel and other metal wire up to 1/8" diameter.

Enlarge the end of a tube to allow a second piece of the same diameter to fit inside.

Designed for building and maintaining equipment with tubes that pass through perforated metal sheets, these expanders have rollers and tapered noses to ensure uniform tube tightness.

Mount these flarers in a vise and create single and double 37° and 45° flares.

Flare soft metal tubing.

Use these tools to flare both soft and hard metal tubing.

Tap this tool with a hammer to quickly form 45° flared ends in copper tubing.

Heat PVC conduit and pipe, then manually bend it to your desired angle.

Ratcheting action gives these tools greater leverage than standard tube benders for bending thick‐wall material.

Protect thin-wall tubing from crimping and collapsing while bending by hand.

Follow the easy-to-read markings to bend conduit to the angle you need.

Create smooth, accurate bends in round heat pipe for routing heat away from sensitive electronic components and toward a heat sink.

Make on-the-fly bends in Schedule 40 PVC conduit and pipe without the risk of kinks or cracks. Lightweight and flexible, these benders are easy to keep on hand for occasional use and last-minute adjustments.

Make bends up to 135° in fuel, brake, and hydraulic lines.

Protect thin-wall tubing from crimping and collapsing while bending by hand. These sets include sleeves for 6 different tube sizes.

Powerful enough to bend conduit and pipe to the angle you need with one stroke of the pump, these are for use on Schedule 40 pipe.

Bend more than one size of tubing without adjusting the bending head.

Flatten bumps, bends, and curves on coiled wire with these straighteners.

Place on the back side of your workpiece to act as a support when you strike it. Also known as dolly blocks.

These hammers have a head loaded with metal shot for added weight and a controlled impact with minimal rebound. Use the domed end of the head for forming soft metal, rounding off edges, and closing rivets. The flat striking face is for driving nails, pins, punches, and chisels.

Set solid rivets by hand. These tools are also known as paneing, setting, and seaming hammers.

To suit a range of applications, these sets include hammers in a range of sizes and weights. Use the domed end of the head for forming soft metal, rounding off edges, and closing rivets. The flat striking face is for driving nails, pins, punches, and chisels.

Strike metal, concrete, and stone with the flat end of these hammers; the wedge-shaped end is for bending and shaping metal. They're also known as cross-peen hammers.

The face and head are made of aluminum-bronze that is Factory Mutual approved, so these tools inhibit sparking, resist corrosion, and are nonmagnetic. Use the domed end of the head for forming soft metal, rounding off edges, and closing rivets. The flat striking face is for driving nails, pins, punches, and chisels.

Make smooth cuts on flat surfaces.

Carve patterns and designs in wood and other soft materials.

A guard protects your hands from hammer blows. These are also known as electrician's chisels.

Use on cement, cinder block, brick, and veined stone.

These are also known as cold chisels.

Score, cut, and trim bricks and blocks.

FM approved for use in hazardous environments, these nonmagnetic, corrosion-resistant aluminum-bronze chisels inhibit sparking.

Use these grinders for occasional bench grinding, tool sharpening, and buffing.

Pedestal grinders let you mount your grinder to work at a comfortable height.