Extra-long bits allow access to hard-to-reach fasteners.

Tighten and loosen fasteners at an angle by pivoting the head on these sockets.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are made to withstand the high torque and force of impact tools.

Switch out worn or damaged bits instead of replacing your entire bit socket.

The short bit on these sockets fits in spaces where height clearance is limited.

In addition to a standard square drive, the sockets in these sets have a hex-shaped base so you can use a ratchet wrench along with an open-end or box wrench for additional leverage.

Tighten or loosen hard-to-reach fasteners with the extra-long bits in these socket sets.

These sockets are also known as pin-in-hex or pin-in-socket bits.

The handle on these assorted ESD-safe screwdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include an assortment of drivers that allow you to apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

The handle on these assorted ESD-safe nutdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening.

Cleaned and double bagged in an ISO Class 5 (Fed. Std. Class 100) clean room, these screws are ready to use on chambers and components in high-vacuum systems.

Often used to fasten parts in engines and turbines, these are our strongest stainless steel screws. They are comparable in strength to alloy steel with the corrosion resistance of 18-8 stainless steel.

Plastic screws are chemical and oil resistant, nonconductive, and lightweight.

Our most corrosion-resistant metal screws, titanium screws withstand salt water, acids, and chemicals. They have a high strength-to-weight ratio and are about 40% lighter than steel screws.

Made of alloy steel, these low-profile screws are nearly twice as strong as their stainless steel counterparts. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water. Use these low-profile screws where space is limited.

More corrosion resistant than 18-8 stainless steel screws, these 316 stainless steel screws have excellent resistance to chemicals and salt water. Their ultra-low-profile lets them fit in the tightest spaces.

With a tensile strength of 170,000 psi, these alloy steel screws are among the strongest we carry. They are stronger than Grade 8 steel screws and are nearly two and a half times stronger than stainless steel thread-locking screws. They have a thread locker to prevent loosening from vibration.

A rubber O-ring under the head of these screws prevents leaks and seals out contaminants.

Fasten these screws inside a high-vacuum system without bringing in contaminants.

A freely rotating washer distributes pressure over a wider area than a flange, preventing damage to your material's surface.

More corrosion resistant than 18-8 stainless steel screws, these metric screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

To vent fluids and gases trapped under the screw, these metric screws are drilled through the shaft.

316 stainless steel screws resist corrosion from chemicals and salt water better than 18-8 stainless steel screws. They may be mildly magnetic.

These metric alloy steel screws are nearly twice as strong as stainless steel button head screws.

As strong as alloy steel and about 40% lighter, these metric titanium screws are known for their high strength-to-weight ratio. They stand up to salt water, acids, and chemicals.

These metric 316 stainless steel screws resist corrosion from chemicals and salt water better than 18-8 stainless steel screws. They have a flange that distributes pressure across a wide surface, eliminating the need for a separate washer. Screws may be mildly magnetic.

With a flange comparable in size to a washer, these metric screws distribute pressure better than standard flanged screws. Made from 316 stainless steel, they have excellent resistance to chemicals and salt water. Screws may be mildly magnetic.

Made from aluminum, these metric screws are lightweight and resist corrosion in wet environments. The flange is wider and thicker than our other flanged screws, so they distribute pressure the best.

To vent fluid and gas trapped under the screw, these metric screws are drilled through the shaft. Made from 18-8 stainless steel, they have good chemical resistance and may be mildly magnetic.

These metric 316 stainless steel set screws have excellent chemical resistance and can be used in saltwater environments.

Made from alloy steel, these metric set screws have a thin edge that digs into hard surfaces for a secure hold. They have a nylon locking patch that grips threads to resist loosening.

These metric alloy steel set screws dig into hard surfaces for a secure hold. They have serrations on the cup edge that grip the material surface to resist loosening.

These metric 18-8 stainless steel set screws are chemical resistant. The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

These metric set screws have a tip that makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

Made of chemical-resistant 18-8 stainless steel, these metric screws have an extra-soft nylon tip that reduces the noise, vibration, and damage that can occur from metal-on-metal contact. Use them on soft surfaces such as aluminum.

Available in metric sizes, these screws have a tip that is harder than nylon and silver to provide a secure hold on hard surfaces. The body is 18-8 stainless steel for good chemical resistance.

These metric 18-8 stainless steel set screws are chemical resistant. A pointed tip wedges into the contact surface for a secure hold on soft materials such as brass.

These metric set screws have a protruding tip that locks within a mating hole or slot to keep parts aligned. They're also known as dog-point set screws.

A low-profile flat-faced ball tip allows these metric set screw to be used in low-clearance applications.

The metric-sized threads on these screws are the same diameter as the shoulder. Comparable in strength to Class 12.9 steel.

These screws have metric thread sizes. They are 18-8 stainless steel for good chemical resistance.

For metric thread sizes with excellent resistance to chemicals and salt water, choose these 316 stainless steel shoulder screws.

These metric screws have a head height that's about two-thirds the head height of a standard shoulder screw. Use them in low-clearance applications such as inside machines.

Install and remove these metric shoulder screws by hand or with a hex key.

These metric 316 stainless steel shoulder screws are more corrosion resistant than 18-8 stainless steel shoulder screws. They also have excellent resistance to chemicals and salt water.

Offered in metric sizes, these brass shoulder screws are electrically conductive, nonmagnetic, and have good corrosion resistance.