McMaster-Carr logo
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    5 Products

    Sealing Washers

    Prevent leaks while distributing weight evenly under nuts and screws. These washers compress as you tighten to keep air and fluid in, and dust and contaminants out. Use them anywhere you need a tight seal, such as protecting electronics from moisture or keeping lubricants contained in machinery.
    Metal
    Image of Product. Front orientation. Sealing Washers. Metal.
    Also known as crush washers, these are made of soft metal that deforms under pressure to fill gaps around the nut or screw. Often found in oil drain valves, they withstand stress and wear better than plastic and rubber washers, but aren't as leak-resistant. Metal sealing washers are not reusable.
    Copper—Softer than aluminum washers, these deform easily to create a tight seal with less effort. They resist rusting in corrosive environments, but will develop a green patina over time.
    For Screw
    Size
    ID,
    mm
    OD,
    mm
    Thk., mm
    Specs.
    Met
    Pkg.
    Qty.
    Pkg.
    Copper
    M33
    33.30038.9001.8 to 2.2DIN 76035000000000000000
     

    General Purpose Washers

    Your go-to metal washer for every screw size. Washers take the pressure off nuts and screws to protect mounting surfaces.
    Steel
    Image of Product. Front orientation. Washers. General Purpose Washers.
    Steel—Best for dry environments since moisture will cause these washers to rust.
    For Screw
    Size
    ID,
    mm
    OD,
    mm
    Thk., mm
    Specs. Met
    Pkg.
    Qty.
    Pkg.
    Steel
    M33
    36.060.04.0 to 6.0DIN 126, ISO 7091100000000000000
     

    Split Lock Washers

    Image of Product. Front orientation. Lock Washers. Split-Lock Washer.
    Stop nuts and screws from loosening due to mild vibration. As you tighten, the uneven ends bite into the nut or screw so it won't back out. While they're not as vibration resistant as other lock washers, they are a great fit for electrical panels, light fixtures, and other light duty assemblies. Split lock washers are not reusable, and they only work with fasteners that have right-hand threads.
    Zinc-Plated Steel—A common choice for areas with occasional exposure to moisture.
    For Screw
    Size
    ID,
    mm
    OD,
    mm
    Thk., mm
    Specs.
    Met
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
    M33
    33.555.25.8 to 6.2DIN 127B5000000000000000
     

    Extreme-Vibration-Resistant Wedge Lock Washers

    When it's critical to keep bolted assemblies secure, choose these two-piece lock washers with the tightest grip of all. They stop nuts and screws from loosening in heavy machinery that experiences jarring starts and stops, such as compressors and compactors. Serrations on the outside bite into the fastener and mating surfaces, while wedges on the inside lock the two pieces together. When the nut or screw starts to loosen, the wedges drive more tightly together to maintain tension. You can reuse these washers up to fifteen times, as long as the serrations and wedges are not worn down. They are comparable to NORD-LOCK® or Sherex TEC® washers.
    Wedge Lock
    Image of Product. Bottom orientation. Lock Washers. Wedge-Lock Washer.
    Super-Corrosion-Resistant 316 Stainless Steel—Superior to 18-8 stainless steel, these washers won't degrade when exposed to harsh weather, salt water, and most chemicals.
    Super-Corrosion-Resistant Zinc-Flake-Coated Steel—With 40 times the corrosion resistance of zinc-plated steel, these withstand rust as well as 316 stainless steel. They have been tested to extreme standards, including 1,000 hours of salt spray. They are similar to Magni-coated washers.
    For Screw
    Size
    ID
    OD
    Thk.
    Pkg.
    Qty.
    Pkg.
    Super-Corrosion-Resistant 316 Stainless Steel
    1 1/4", M331.350"1.910"0.260" to 0.280"1000000000000000
     
    Super-Corrosion-Resistant Zinc-Flake-Coated Steel
    1 1/4", M331.350"1.910"0.220" to 0.240"10000000000000
     
    back to top