We will reply to your message within an hour.
Conveyors are made of corrosion-resistant stainless steel, making them suitable for washdown applications.
For more demanding shipping and assembly applications, these conveyors can carry heavy loads. They are made of corrosion-resistant stainless steel making them suitable for washdown applications.
Made from stainless steel, these rollers are suitable for washdown applications. They have a standard 1.9" diameter to fit most roller conveyors.
Choose the width you need from 6" to 60" in 1/16" increments.
These rollers have diameters 1 3/4" and below.
All stainless steel construction makes these rollers suitable for washdown applications. They have 2 1/2" diameters.
Replace worn and damaged bearings or press-fit bearings into tubing or pipe to create a roller.
Use these bearings to replace worn and damaged bearings or press-fit them into tubing or pipe to create a roller. All have a hex-shaped axle.
Also known as sprocket-driven conveyor belting, sprockets drive the belt.
The corrosion-resistant stainless steel construction makes these pulleys suitable for washdown applications.
This low-profile lacing requires only a hammer to install so it's good for repairs and tight spaces. Also known as alligator lacing, the lacing teeth bite into the belt to hold. Use on belts up to 0.31" thick.
Insert a pin into the lacing and lock it in place by bending the ends at a 90° angle.
Also known as alligator lacing, this strong, impact-resistant lacing uses a staple driver and installation guide to secure staples. Use on 0.0625" to 0.25" thick belts.
Our heaviest duty lacing uses bolts and nuts to repair and extend 0.25" to 0.625" thick belts.
A tensioner extends or retracts the conveyor pulley to adjust the tension on the conveyor belt.
Use on a conveyor pulley with a conveyor belt tensioner to adjust the tension on a conveyor belt.
These tensioners have a totally enclosed adjusting screw to prevent debris buildup and thread damage.
Use these belt scrapers to remove debris from conveyor belts. Place at the end of a conveyor where it returns.
Use these belt scrapers to remove debris from conveyor belts. If a chip of this blade breaks off near a process line, it can be located by metal detectors to reduce contamination risks in food processing applications.
A clamp on one end grips conveyor guides or rods.
Use brackets and connectors to create vertical and horizontal support arms.
Use the hole at the end of these rods to attach sensors and accessories without clamps.
These rods have a bracket on the base so they're ready to mount.
The pivoting joint on these rods makes angle-mounting easy.
Graduated in 1/8" or 1 mm increments, these rods make it easy to align multiple brackets during installation.
To make aligning multiple brackets during installation easy, these rods have 1/8” graduation marks. They also have a pivoting joint, so you can adjust the angle of your mount.
Clamps hold guide rails in place or join ends of a rail together.
Brackets mount to the frame of a conveyor to hold mounting rods.
Also known as cross blocks, these connectors join rods at different angles.
Keep materials orderly and separate products into distinct lanes.
Suspend trays, plates, and drip pans underneath a conveyor.
These brackets mount to the frame of a conveyor to hold guide clamps.
Brackets are sized to mount sensors and reflectors to a conveyor frame.
Install these ball transfers in a threaded hole or use a nut to secure.
A double-sealed ball keeps out dirt and debris, and side vents expel contaminants.
These ball transfers have capacities up to 2,200 lbs.
The flange has mounting holes for fastening.
To keep out dirt and debris, these flange-mount ball transfers have a double-sealed ball and side vents that expel contaminants.
A thick rubber cushion underneath these ball transfers absorbs impact and reduces vibration.
Transfers recess into the mounting surface for a low profile.
With a ball recessed into the mounting surface, these ball transfers have a low profile. Their double-sealed ball keeps out dirt and debris, and side vents expel contaminants.
The ball in these transfers is spring-loaded to absorb impact.
Drop-in design makes for easy installation.
These ball transfers have capacities up to 3,300 lbs.
These ball transfers and stops rise when you supply air and retract into the housing when air supply ceases.
Replace damaged wheels or use multiple wheels to build a custom conveyor.
Add on to an existing screw conveyor or keep it running like new.
Mount brushes by sliding them into a holder. Holders can be cut to size with a hacksaw.
Air powers these vacuums to create a powerful inline conveyor that moves small parts, shavings, and bulk solids.
Vacuums have threads on the intake and exhaust ends for use with threaded pipe.
Coiled-metal construction provides flexibility to bend around small-diameter pulleys and accommodate curved belt drives and misaligned pulleys.
Often used to join conveyor belt seams, use this lacing for a tight hold with uniform tension across the width of your belt.
Weigh boxes as they flow through your conveyor line to reduce bending and lifting.