Position components in assemblies, as well as separate or connect parts with these standoffs.

A nylon patch bonded to the threads adds friction, preventing these standoffs from loosening from vibration.

Choose these standoffs for their adherence to NAS 1831 specifications.

Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.

Made of aluminum, these spacers are lightweight and mildly corrosion resistant.

These spacers have excellent corrosion resistance and are passivated for enhanced protection.

The anodized coating on these lightweight spacers provides increased abrasion resistance over uncoated aluminum.

Withstanding salt water, acids, and chemicals, these spacers resist corrosion better than any other metal spacer we offer. They have a high strength-to-weight ratio and are about 40% lighter than steel spacers.

Almost nonabsorbent, these unthreaded LDPE and HDPE spacers won't swell when exposed to water.

PTFE spacers have a slippery surface and surpass most plastic spacers when it comes to chemical resistance and performance in extreme temperatures.

Use PEEK spacers as an alternative to metal spacers in high-temperature, high-stress applications. They resist chemicals, wear, and moisture.

Protect components from electrical charges.

Reduce vibration, shock, and noise with these spacers that compress between components.

A nickel-chrome plating gives these spacers a mirror-like finish.

Also known as captive standoffs, a recess under the hex clinches the panel for a strong hold that won't push, pull, or twist out. When mounted, the hex sits flush with the surface and the closed end creates a neat, finished appearance.

These standoffs are designed to fit in the limited space of compact electronics such as laptops and hand-held devices.

Both ends snap and lock in place for a permanent connection.

Secure the self-tapping female connection with a screw; the other end snaps snugly into a panel, yet can be released for repairs and upgrades.

Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.

The flat top supports boards without drilling a hole while wings on the other end add tension for a secure hold in a hole.

Once the end is clinched in place, panels with keyholes easily slide on and off these supports.

These coupling nuts have good chemical resistance.

More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.

About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.

The left-hand threads on these coupling nuts resists loosening from counterclockwise vibration. Use in light duty applications.

Choose these locknuts to fasten standard metric threads. They’re Class 8 steel, so they can be used in most fastening applications.

These metric-sized coupling nuts are Class 10 steel, so they’re about 25% stronger than medium-strength steel coupling nuts.

One-third the weight of steel, aluminum coupling nuts resist corrosion in wet environments.

Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.

Known for their strength, steel coupling nuts are available with a corrosion-resistant finish.

Taller than standard hex nuts, these metric nuts provide a larger gripping area for installation with a wrench.

Change thread sizes or types, such as fine to coarse threads, on parts without changing gender.

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Need to join two female-threaded parts, such as coupling nuts, with dissimilar inch thread sizes? Attach them to these adapters and tighten the exterior hex nut for a secure connection.

Twist these adapters onto female metric threads to change pitch or switch thread sizes.

Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.

Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.

Also known as shoulder washers.

These washers have a flat bottom and high walls to protect metal screw heads from electrical current.

Connect and separate threaded rods, studs, and other components. These hollow rods have internal threads on both ends, so you can make connections and still pass wiring and other objects through the center of the rod.

Also known as shoulder and insulator washers, these nonmetal washers block electrical current and prevent corrosion from mating different types of metal.

These aluminum inserts are lightweight, nonmagnetic, and mildly corrosion resistant.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

Use where high loads and speeds are not required.

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.

An aluminum shell adds strength.

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

Also known as Oilite® bearings.

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Support heavy loads that are often found in bottling and filling lines in food plants—these bearings contain extra iron and FDA-compliant oil. They’re flanged, so they handle loads both parallel and perpendicular to the shaft.

These bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Use where high loads and speeds are not required.

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

Graphite provides a layer of dry lubrication that can operate in high-temperature environments.

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Good for underwater applications, these bearings won’t swell or warp when wet.