Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Thick leaves and a large diameter pin make these hinges good for use with heavy doors.

These hinges are made of metal.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

A grease fitting makes these hinges easy to lubricate.

The hinge pin is attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Springs in these hinges without holes automatically swing doors and gates closed behind you.

After a light push on the door, springs in these hinges swing doors and gates fully open.

These hinges without holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

No need for oil or grease, these hinges are maintenance free. The mounting holes form an industry-standard half-moon shape.

Only one cutout (mortise) is needed to mount these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

These hinges are made of metal.

The leaves of these hinges almost touch when the door is closed. They are often used in electrical enclosures for a tight seal.

With large pin diameters for added strength, these hinges can hold heavier doors and gates than other strap hinges.

Bearings allow these hinges to open and close doors smoothly.

These hinges have a standard range of motion of 100° to 120°.

With a 170° range of motion, these hinges are for doors that need to open wide.

Easier to install than other concealed cabinet hinges, these do not require a cutout.

Surface-mount these hinges to the side of a cabinet.

Provide smooth motion between two pieces of strut channel.

No need for fasteners—friction holds this framing together. Use press-fit framing and fittings to assemble carts, enclosures, and partitions.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

Gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

Providing constant resistance through the full range of motion, these supports hold lids open at any angle up to 70° or 90°.

These internally threaded rod ends have an eyelet and a ball that swivels to support angular misalignment. Also known as rod-end bearings.

Connect your grease gun to the fitting to lubricate. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

An oil-embedded bronze insert slowly releases lubricant throughout the life of these internally threaded rod ends.

These internally threaded rod ends have an oil-embedded bronze insert that slowly releases lubricant over time. Connect your grease gun to the fitting to relubricate.

With at least 55° of ball swivel, these externally threaded rod ends accommodate greater misalignment than any other we offer.

Made of cadmium-plated steel, these externally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made to extremely tight tolerances, these externally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Seals keep out dirt and an oil-embedded foam insert slowly releases lubricant for a long life.

These internally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

An innovative body design keeps the ball from being pushed out when supporting thrust loads.

A double row of precision ball bearings allows high speeds and smooth operation.

These alloy steel rod end bolts have the highest tensile strength of any steel fully threaded rod end bolt we offer.

Also known as swing bolts and eyebolts, these internally threaded rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

To reduce noise and vibration, these bolts have a rubber bushing—connect them to rods, pipes, tubes, and cable linkages that have female threading. They’re also known as isolated rod ends.

These alloy steel bolts have the highest tensile strength of any blank rod end bolt we offer.

These steel rod ends are machined to SAE standards.

Thread or weld the unfinished shank of these rod ends to meet your specific linkage needs.

Able to stand up to frequent use, these linkages offer excellent wear resistance. They consist of ball joint rod ends with a ball stud attached to simplify mounting.

These internally threaded linkages have a slippery PTFE liner that reduces wear and eliminates the need for lubrication.

An oil-embedded bronze insert slowly releases lubricant throughout the life of the joint.

Along with excellent wear resistance, these linkages have a grease fitting for easy lubrication. An internally threaded rod end connects to threaded rods, studs, and other parts with male threads.

A spring-loaded sleeve allows for rapid assembly and disassembly. These ball joint linkages are made of steel.

Use these linkages to create inline pivoting connections. They have internal threads on one end and external threads on the other.

Also known as spherical bearings, swivel joints support angular misalignment. Press them into a hole or housing where a ball joint rod end won’t fit.

A unique design allows these joints to support heavy one-direction thrust loads as well as combined radial/thrust loads.

Turn the padlock eye to fasten these hasps without a padlock.

Mount these padlockable eyes to the front of a door and door frame.

Mount these hasps around complex curves, angles, and corners that other corner hasps can't reach.

Choose this hasp if you need several hasps that open with the same key.

Like two lockout hasps in one, there's a jaw at each end with different clearances for added versatility.

The fold-over closing design hinders prying, while a slot instead of holes makes it easy to install multiple padlocks.

In addition to an overlapping hasp that interlocks when closed, lockouts have a chain that attaches to equipment so they won't get lost.

In addition to a hasp that interlocks when closed, lockout has an adapter to lock out a valve and a chain that attaches to equipment so it won't get lost.

Add legs to these brackets and mount to a tabletop to create a folding table.