This welded, one-piece strut channel combines two strut channels back-to-back.

Up to two times the height of regular strut channel, this high-profile channel is stronger than regular strut channel.

Slide the strut channel into the tube for telescoping length adjustments.

For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.

Designed to wrap around the sides of strut channel, these brackets provide a stronger hold than other strut channel brackets.

These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.

A spring plus serrated grooves that grip the lip of the channel provide a more secure hold than standard strut channel nuts.

Connect two channels to create a stacked channel.

There's no need for additional fasteners with these nuts—they combine a strut channel nut with a spring and a threaded stud.

Insert these nuts into the long open side of strut channel and twist to secure. A built-in washer enables one-handed installation.

A tab fits tightly against the lip of the channel to keep these nuts from slipping.

Use with hex nuts to connect threaded rod.

Notches on these washers grip the channel to keep them in place.

Securely fasten strut channel to the floor.

Mount a length of strut channel between the ends of a beam to run cable and conduit along the beam without drilling.

Brackets mount on the outside of strut channel to allow trolley movement.

Cover rough ends of strut channel.

Position two strut channels at a 30° to 60° angle, then tighten the bolt to secure.

Provide smooth motion between two pieces of strut channel.

Slip these hangers onto the lip of top-opening strut channel to attach chain, wire rope, pipe, and threaded rod.

Route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

These general purpose gas springs assist in opening lids, covers, windows, conveyors, and seats—similar to a hatchback opening on a car.

Mechanical operation means these springs have no seals to fail or gas to leak.

A temperature-resistant seal allows these gas springs to withstand heat up to 392°F.

Made from stainless steel for excellent corrosion resistance in damp environments.

Made from stainless steel for excellent corrosion resistance in damp environments.

Automatically locking when fully extended and made of 316 stainless steel to resist corrosion, these gas springs protect material and equipment underneath heavy loads in damp environments.

Release gas from these springs until they supply the exact force you need—made of corrosion-resistant 316 stainless steel, they’re commonly used in wet environments.

Made from stainless steel for excellent corrosion resistance in damp environments. These gas springs have a bleed valve so you can release gas to permanently reduce the force to meet your requirements.

Color coded by force to help you choose the correct replacement, these gas springs generate high force.

Attach eyelet end fittings to these brackets to mount gas springs.

These brackets secure eyelet end fittings from both sides to provide a strong hold on gas springs that get bumped or jostled. Mount on any panel, lid, or door.

Pair these 90° angle brackets with ball socket end fittings to mount your gas spring in almost any position.

About twice as thick as standard 90° angle ball stud mounting brackets, these brackets are suitable for high-force applications.

Stainless steel that’s twice as thick as standard 90° angle ball stud mounting brackets makes these brackets good for high-force applications exposed to damp conditions.

Made from stainless steel for excellent corrosion resistance in damp environments.

Since they’re at least twice as thick as standard ball stud mounting brackets, these brackets are best for high-force applications.

Made from stainless steel for excellent corrosion resistance in damp environments.

Easy to machine, these brackets are made from aluminum—drill mounting holes where needed.

Attach ball socket end fittings to these studs to mount gas springs.