These pumps can be submerged or connected remotely to a pipe in your line. Use them to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Protected from impact by a durable epoxy-coated aluminum housing, these pumps can be submerged or connected remotely to a pipe in your line. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps can be submerged or connected remotely to a pipe in your line. Magnets turn the impeller so there's no shaft seal to wear out. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Submerge these pumps to circulate machine and cutting oil with a viscosity up to 9 centipoise.

Circulate salt water in submerged and open-air applications.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. Equipped with a large intake and rugged impeller, they transfer raw sewage water with solids up to 2” in diameter. The float switch is wired to the pump.

Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2” in diameter.

Pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Connect them to a three-pronged plug or wire them directly to a power source to activate. Pumps transfer raw sewage water with solids up to 2” in diameter.

Also known as grinder pumps, these pumps have stainless steel blades that prevent clogs by breaking down sewage into an easy-to-transfer slurry. The float switch is wired to the pump.

Pumps have a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Use with debris-free water.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use with debris-free water.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F.

The intake is 2" from the base of the pump to prevent dirt at the bottom of your sump pit from clogging the pump. Use with debris-free water.

Convenient for applications where a sump pit is impractical, these pumps include a basin. Use with debris-free water.

The float switch is wired to the pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.

Move higher volumes of water with solids than other sump pumps. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

Activate your pump in dirty water that contains sludge and sewage.

Hang these switches in a sump pit to detect rising water levels.

Place your pump inside these basins for ground-level applications and below-ground use without a sump pit.

Kits include tubing, a backflow-prevention valve, an adapter, and a clamp.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Kits include 20 feet of PVC suction hose, 50 feet of PVC discharge hose, a suction strainer, and two steel thread adapters.