These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

These rings meet military specification MS 16624.

Thicker than standard external retaining rings, these rings withstand greater force.

The curved design of these rings works like a spring, taking up play for a tight hold.

Often used with small engines, heavy equipment, and power transmission, these external retaining rings have speared ends to help you install and remove them.

Also known as constant-section rings, these rings have open ends and a profile that does not taper like other external retaining rings. Use them with linear bearings on support rail shafts.

These coiled rings can be wound into place on a shaft without tools.

Thicker than standard spiral rings, these rings withstand greater forces.

These rings are reinforced to withstand faster rotation than other side‐mount retaining rings. Also known as reinforced E‐style rings.

Also known as bowed E-style rings, these have a curved design that works like a spring, taking up play for a tight hold.

Also known as poodle rings, these thick rings have "ears" that form a large retaining surface to withstand stronger forces than other side-mount retaining rings.

Slide these rings into place with one twist—no tools required—for applications with high thrust loads.

Squeeze these rings to place them in the groove inside a bore or housing.

Thicker and stronger than standard internal retaining rings, these withstand greater thrust loads.

The curved design of these rings works like a spring, taking up play for a tight hold.

Slide these rings into place by hand with a single twist for applications with high thrust loads.

These assortments include pliers to install external and internal rings.

Wind these retaining rings into a groove—no tools required for installation.

Assortments include pliers to install external and internal rings.

Pull ring ends together with retaining ring pliers and place into the bore of a shaft or housing.