Able to withstand high currents, these switches are often used with motors and pumps.

Protect toggle switches from moisture and dust by replacing panel mounting nuts with these rubber covers.

A nickel-plated brass cap protects toggles from impact.

Seal the panel cutout around a toggle switch.

These rubber covers protect switches from splashing liquid.

These switches are protected from corrosion, high-temperature and high-pressure washdowns, and oil/coolant spraying. Install them in 22 mm dia. cutouts.

Maximize space in a panel—these switches are smaller than most standard rocker switches.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Apply pressure from any direction to actuate these switches.

When the pedal is pressed, the built-in potentiometer adjusts the resistance to vary the speed for motor drives.

Rated IP67 and NEMA 6, these switch mats withstand washdowns.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited.

Made with stainless steel conductors, these switches resist corrosion in damp areas. They’re less than 1/4” thick, so they’ll fit under floor mats and in other tight spaces.

Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment.

Intuitively steer and position cranes, robot arms, and other machinery that moves in multiple directions—your equipment will follow the movements you make with these joysticks.

Built for tight spaces exposed to water, these switches have a housing that's less than 1" long and IP67 rated for protection from temporary submersion.

Trigger actions in devices as small as phones and drones. The smallest snap-acting switches we offer, these switches fit into the tiniest of spaces and help keep weight to a minimum.

Minimize false triggers—these switches require 10 lbs. of actuation force in order to shut off machinery immediately.

Detect objects as thin as a freshly sharpened pencil tip. These switches are best for tight spaces because they have a smaller light beam and can detect smaller objects than standard photoelectric switches.

Mounted to your circuit board, these switches trigger when magnetic components get near, and reset as they move away.

Mount these switches to a flat surface or attach to DIN rail.

Install these switches in a panel cutout.

Isolate input and output circuits to prevent damage from voltage spikes, reduce signal interference, and amplify signal.

Fit these relays where standard spade-terminal relays are too big.

Smaller than relays with electrical wiring, these relays fit in compact devices. Mount them through holes on circuit boards with their solder pin terminals.

Reduce connection errors on circuit boards that control machine guards and other safety devices. These relays take up less space on a board than those with electrical wiring because their solder pin terminals mount directly through circuit board holes.

These relays switch through a series of different circuit configurations every time they receive an input voltage. Also known as step relays.

Protect electrical equipment from overcurrent and undercurrent damage—these relays continuously monitor current flow.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

With a round body that’s at least one-third thinner than traditional pressure switches, these fit in tight, cramped spaces.

Compatible with most air systems, these switches send digital signals to a programmable logic controller (PLC) to trigger separate processes when they reach either of their two set pressures. For example, they’ll activate a compressor if the pressure is too low or a relief valve if the pressure is too high.

With a set pressure range that works for most air systems, these switches send signals when your air system reaches a set pressure to your programmable logic controller (PLC) to activate automated controls and alarms.

Specifically made for air systems, these switches send signals to your programmable logic controller (PLC) to trigger processes when they reach a set vacuum.

Designed specifically for air systems, these switches send signals to your programmable logic controller (PLC) to activate controls or alarms when your system reaches a set pressure or vacuum.

The faceplate on these controllers is sealed to meet NEMA 4X and IP66 for protection in washdown environments with splashing water, corrosive liquid, and dust.

Cycle heaters on and off intermittently to maintain a set temperature in your system.

Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch.