We will reply to your message within an hour.
A rubber seal protects these switches from splashing water.
Because these switches mount flush against a panel, they're easy to clean and hard to damage.
Install in 14 mm dia. cutouts.
Install in 12 mm dia. cutouts.
Rated NEMA 4X and 13, all switches resist corrosion and can withstand washdowns and oil/coolant spraying.
More lightweight than steel or stainless steel, these aluminum enclosed switches are rated NEMA 4X for protection from corrosion and washdowns.
Rated IP67 for protection from dust and temporary submersion.
Rated IP67, these switches are protected from temporary submersion.
Choose an actuator and contact block to make your own 22 mm plastic switch.
With a slim shape, these switches fit comfortably in your hand.
Immediately cut power by pulling the cable.
The light touch of a finger turns circuits on and off without pressing down a contact.
Rated IP67 and NEMA 6, these switch mats withstand washdowns.
Small enough to fit in the tiniest spaces, these switches are rated IP67 for protection from temporary submersion.
Stack these slim switches together, or fit them into tight spaces. They're rated IP67 for protection from temporary submersion.
Secure these switches into panels using mounting nuts.
Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.
Rated IP67, these switches are protected from temporary submersion. When an object in motion comes into contact with the actuator, it sends a signal to open or close a circuit.
Sealed actuators prevent these switches from jamming, even when exposed to sand, mud, or dirt. They're rated IP67 for protection from temporary submersion.
These switches actuate with the slightest push for a high degree of accuracy. They're rated IP67 for protection from wet locations and temporary submersion.
Often used on conveyor systems and bin filling operations, these switches have the rapid-closing action of a snap-acting switch but have a large actuator for sensing larger objects.
Shorter and thinner than other safety limit switches, these are sized to fit tight spaces.
Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.
Protect machinery and ensure the safety of personnel—these switches will open the circuit when actuated even if a spring fails or the contacts stick.
Often used with machine guards, these switches mount to a door frame.
Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.
These switches use DC input voltage and produce PNP or NPN signal output. They're often used with programmable logic controllers (PLCs).
Use these switches to sense metallic objects in environments containing flammable gases and combustible dust. ATEX and IECEx certified to protect against explosion, they produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks.
With a smaller diameter and shorter length than standard sized switches, these fit in the most space-constrained areas.
The flexible cable on these switches withstands applications that require frequent motion, such as robotics.
Easily mount these flat switches to a base or rail.
The short body on these switches makes them suitable for tight spaces.
Sense objects from farther away than with other DC proximity switches that have the same diameter.
These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.
Twist the sensor to detect metallic objects where explosive dust or gas may be present—the sensor rotates for front, side, top, or bottom sensing. These switches are UL and C-UL listed as well as ATEX and IECEx certified for hazardous locations.
Sense objects as they pass through the switch’s ring via tubing or a funnel. These switches are often used to monitor blockages, detect breaks in spooling wire, or count small metallic parts, such as screws, during the stamping process.
For use in volatile areas, these intrinsically safe switches detect objects when they pass through the slot. They use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or create sparks. ATEX and IECEx certified, they protect against explosion.
Mount these intrinsically safe switches to flat surfaces in volatile areas. Their low-current, low-voltage NAMUR signal means they won’t ignite or create sparks while in use. ATEX and IECEx certified, they meet international standards to protect against explosion where combustible dust and flammable gases are present.
Turn the face on these switches to sense metallic objects from the front, sides, top, or bottom.
These intrinsically safe switches detect objects as they’re routed through the ring. They produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks. Switches are ATEX certified to protect against explosion.
These switches have a longer sensing distance compared to other proximity switches with the same diameter.
Most often found in older devices, these switches require AC input voltage.
Switches accept both AC and DC input voltage.
Rotate the face on these switches five different directions for easy installation and positioning—they work with both AC and DC inputs.
Mount these flat inductive switches to a base or rail to remotely detect metallic objects in wet and dirty environments.
Detect the presence or absence of an object moving at high speeds with a light beam. These switches have a longer sensing distance than proximity and ultrasonic switches.
A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).
With a narrow, flat body, these switches fit in tight spaces.
For optimal performance in tight spaces, these switches have a smaller beam and can detect smaller objects than standard photoelectric switches.
Light beams travel up to 32 ft. between the transmitter and receiver.
These switches have a receiver built into the housing, eliminating the need to align components and measure sensing distance during installation.
The highly flexible fiber-optic cable and small sensing end help you position these switches in hard to reach areas.
Set these switches to delay activation by up to fifteen seconds after detecting an object.
Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.
Safely detect the presence or absence of an object moving at high speeds with a light beam. These switches produce a low-current, low-voltage NAMUR signal, so they won’t create sparks or ignite. ATEX and IECEx certified, they protect against explosion in environments containing flammable gases and combustible dust.
Often used with programmable logic controllers (PLCs), these switches use DC input voltage and produce PNP or NPN signal output.
These switches use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or produce sparks. ATEX certified, they protect against explosion in environments containing flammable gases and combustible dust. Switches sense both metallic and nonmetallic objects.
Detect objects and liquid or material levels to set off actions in your system—regardless of size, shape, or surface finish.
These switches detect magnetic objects—or objects with a magnet attached—through non-magnetic walls.
These switches sense when a valve is open or closed, supporting flow and temperature control within your system and offering reliable feedback.
Support flow and temperature control in your system with these intrinsically safe switches, which sense when a valve is open or closed in volatile areas. They are ATEX and IECEx certified to protect against explosion.
These switches actuate when a magnet comes within sensing distance, and reset when the magnet moves away.
Wire contacts to an alarm system to alert when doors or windows are opened.
Prevent unauthorized use—these switches require coded magnets to actuate. They cannot be bypassed using ordinary magnets.
Often used as position indicators, pump level controls, and machine limit switches, these switches actuate when tilted to a certain angle.
Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.
Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.
Direct flow with an electronic signal.
Send an electronic signal to your system when the piston reaches a certain location.
Set to actuate at a specific temperature, these switches are easy to setup and prevent changes to the setpoint. They have a threaded probe, so they install directly into tanks, pipelines, and other process components to turn equipment on and off at a set temperature.
Send signals to trigger two different processes, each with their own set temperatures.
A digital display makes it easy to monitor the temperature and control when these switches turn heating equipment on and off.
An adjustable reset lets you control the amount of temperature change, also known as deadband and differential, before these switches reset. When they reach the set temperature, they send an electronic signal to your programmable logic controller (PLC) to turn equipment on or off.
With a round body that’s at least one-third thinner than traditional pressure switches, these fit in tight, cramped spaces.
Built with an explosionproof enclosure to meet NEMA 7 and 9 standards for hazardous locations, these switches were tested and verified by UL and CSA for use where explosive liquids, dust, and gas are present.
When these switches reach a set pressure, they send electronic signals to your programmable logic controller (PLC) to activate automated controls or alarms.
Like other 3-A certified sanitary pressure switches, these switches trigger controls and alarms when food-processing, pharmaceutical, and biotech lines reach a set pressure, but they also have a sanitary adjustable setpoint ring that you twist to make quick changes.
When these switches reach either of their two set pressures—both of which can be controlled from a display—they send digital signals to your programmable logic controller (PLC) to activate automated controls or alarms.
Send two digital signals to your programmable logic controller (PLC) to trigger different processes—these switches activate at two set pressures.
When these 3-A certified switches reach a set pressure or vacuum, they trigger controls and alarms in food-processing, pharmaceutical, and biotech lines.
Monitor and control vacuum pumps, air compressors, and hydraulics while viewing readings and warnings on the display.
Two easy-to-set dials allow you to adjust a set activation point for vibration as well as a time delay to avoid false triggering from start-up vibration. An LED alarm signals if the set activation point is exceeded.
A built-in display makes it easy to view vibration levels, warnings, and the status of these switches. Use the push-buttons to set and adjust activation points for vibration as well as a start delay to avoid false triggering from start-up vibration.
Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch.
Detect when oil rises on water, foam forms on beer, and tanks empty, triggering pumps and valves in food and sanitary lines. These switches are 3-A and European Hygienic Engineering and Design Group (EHEDG) certified since they’re easy to keep clean.
When these switches reach a set flow rate, they send digital signals to your programmable logic controller (PLC) to activate automated controls or alarms.
Easy to clean and install, these flow switches are 3-A certified to meet sanitary design standards and insert into your line with a quick-clamp mounting adapter. They send digital signals to your programmable logic controller (PLC) to activate automated controls or alarms when they reach a set flow rate.
Instead of disassembling your system for inline installation, thread these flow switches onto a mounting adapter and insert them into a pipe tee or pipe outlet. They send digital signals to your programmable logic controller (PLC) to activate automated controls or alarms when they reach a set flow rate.
Send flow rate measurements to monitor and control equipment.
Send flow rate and temperature measurements simultaneously to a programmable logic controller (PLC), data logger, or other receiving device.
Also known as magmeters, these transmitters use a magnetic field to measure flow rate and temperature with high accuracy.
Thread a ring fitting into your pipe connection and insert the probe of these transmitters to measure the flow and temperature of water, oil, or air.
Measure and transmit flow rate, pressure, and temperature of industrial gases, such as air, argon, CO2, and nitrogen, flowing through your system.
Measure the distance to objects and the level of liquids and materials despite size, shape, or surface finish, and send that information to other parts of your system.
These IP67 rated lights withstand temporary submersion in a maximum of one meter of water for up to 30 minutes. They're compact for easy transport to job sites with no electrical power.
Rated for use in environments where hazardous material is present.
These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.
Gooseneck arms can be repositioned faster and more easily than articulating arms.
The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.