Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.

These standoffs are made to NAS specifications.

A nickel-chrome plating gives these standoffs a mirror-like finish.

The magnetic end of these standoffs makes it easy to temporarily mount or reposition components on magnetic surfaces.

Also known as captive standoffs, a recess under the hex clinches the panel for a strong hold that won't push, pull, or twist out. When mounted, the hex sits flush with the surface and the closed end creates a neat, finished appearance.

These standoffs are designed to fit in the limited space of compact electronics such as laptops and hand-held devices.

A smooth base on these metric nuts provides more contact with the mating surface than weld nuts with projections

Projections on the base concentrate the weld and provide room for heat to dissipate.

Weld these metric nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.

You can weld these metric nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

Weld these nuts to stainless steel surfaces.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to uncoated steel surfaces.

Threads float inside the retainer of these metric nuts so you can install a bolt at a slight angle to align with off center parts.

These screw-mount nuts are often used to attach glides and levels to wood.

Stainless steel adhesive-mount nuts have excellent corrosion resistance in most environments.

Stainless steel nuts have excellent corrosion resistance in most environments.

Press these metric nuts into a drilled or punched hole with an arbor press or similar pressure tool.

These metric nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts have a zinc plating for corrosion resistance in wet environments.

These press-fit nuts have a nylon insert that grips threads to resist loosening.

Also known as broach style captive nuts, these nuts have good chemical resistance and may be mildly magnetic.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

A hex-shaped body provides the highest twist resistance of any rivet nut.

Once installed these rivet nuts have a large back flange that distributes the load across a broad area for a strong hold in plastic and composites.

About twice as strong as aluminum rivet nuts, these rivet nuts are zinc plated for mild corrosion resistance.

These kits include one size of low-profile rivet nuts.

The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.

The coated flange seals out moisture and prevents corrosion.

These rivet nuts are mildly corrosion resistant.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.

Use these tube-end weld nuts with left-hand threaded fasteners.

Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

The through hole allows you to connect float rods to float valves.

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

The barbed sides keep these securely in place even before a screw is installed.

Made of 18-8 stainless steel, these inserts have good corrosion resistance.

These inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

A black-phosphate finish provides mild corrosion resistance.

These assortments include various sizes of thread-locking inserts.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.

A distorted thread grips the screw to resist loosening.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A dry film keeps the screw from sticking or binding in these inserts during installation.

A dry film keeps the screw from sticking or binding in these inserts during installation.

A distorted thread grips the screw to resist loosening.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

Install these inserts into plastic parts to create a secure base for fasteners.

Large threads cut into softwood such as particleboard for a strong hold.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.

Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.

Hooked prongs give these inserts excellent holding power even when removing screws.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

Knurls hold these inserts in hardwoods such as oak, maple, and walnut to prevent twisting.

An open end allows long screws and bolts to pass through the insert.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

Keep a variety of standoffs in different lengths and thread sizes on hand.