Connect to a compatible ratchet or electric threader to cut external pipe and conduit threads.

Add or replace parts such as drive adapters, die sets, and drive bars for the Ridgid Large Size Pipe and Conduit Threader Adapter.

These machines thread faster than the Ridgid 300 and include a self-lubricating die head and automatic chuck.

Carry this pipe and conduit threader to your work site.

Use these dies with Ridgid pipe and conduit threader die heads on Ridgid pipe and conduit threaders.

Cut threads in PVC with the specially designed teeth on these high-speed steel dies.

Use these dies to create external threads on bolts, studs, and rods.

Create external pipe and conduit threads.

Repair rusted and damaged left-hand screw threads. These dies are hex shaped for use with conventional wrenches.

With a smaller width than regular hex dies, these dies are suitable for repairing rusted and damaged left-hand threads in tight spaces.

Renew rusted and damaged pipe and conduit threads.

Clean and restore the fine threads on power transmission shafts that are used with bearing locknuts. Dies are sized according to the American Bearing Manufacturer's Association (ABMA).

Slide over the end of threaded rod, pipe, and conduit to the area where threads are damaged, then tighten and rotate to repair threads.

One file restores pipe and conduit threads in many sizes.

Use these wrenches to turn hex-shaped dies by hand. They're also known as die stocks.

Sized to cut oversized threads, these tools are often used to tap holes where the threads will shrink due to heat treatment or plating.

Tap threads for left-hand threaded fasteners.

Use these taps on hard and abrasive material, such as heat-treated metal, nickel, and fiberglass.

With a drill bit point to drive into the workpiece, these taps can drill and tap holes in a single step. A 1/4" hex shank connects them directly to tools such as drills and power screwdrivers.

Create oversized threads while keeping chips clear. These taps are sized for use in holes where the threads will shrink due to heat treatment or plating.

Clear chips while tapping deep and hard-to-reach holes. These taps have an extra-long shank for extended reach.

Drill holes and cut threads without switching tools.

With a taper chamfer and bottoming chamfer at opposite ends, these taps start threads easily and are good for threading close to the bottom of closed-end holes.

Tap threads into hardened steel and iron. These cobalt steel taps have straight flutes for high durability.

A high helix angle provides the cutting strength needed to tap threads in titanium. These cobalt steel taps have an open flute design that keeps chips clear, so they don't need to be reversed to prevent buildup.

With an extra-long shank, these taps have extended reach for tapping deep and hard-to-reach areas in pipe and conduit.

Use these carbon steel taps for thread repair and occasional tapping of pipe and conduit. They can tap threads into most metal and plastic, but they have a shorter tool life than standard taps.

Drill and thread holes for pipe and conduit without switching tools.

Also known as short-projection taps, these have fewer tapered threads at the tip than standard pipe taps, so you don't have to drive them as deep to produce full threads.

The cutting teeth are shaped to cut smooth threads in soft pipe and conduit material.

Cut threads in PG thread sizes commonly used for European conduit.

These holders work like sockets to connect taps to ratchet wrenches.

Connect a tap to these wrenches for occasional or light-duty hand tapping. All have a T-handle design, so they're more compact than straight-handle tap wrenches but provide less leverage.

Use with a tap to thread holes by hand. These tools have long handles to provide more leverage than T-handle wrenches, but they require more space for tapping.

Powered by compressed air, these tap wrenches thread holes faster and with less effort than manual tap wrenches.

Drawers and labeled compartments provide space for keeping tools organized. Taps and drill bits are not included.

These steel cases close for easy transport and are labeled with sizes for organizing tools. Taps and drill bits are not included.

Restore bolt, hole, pipe, and conduit threading with this set of four files.

Repair rusted and damaged threads in pipe and conduit. These files are for use in most hole diameters.

Attach these tools to a socket wrench to restore rusted and damaged spark plug threads in two common sizes.

For start-to-finish tapping of left-hand threads, these sets include one taper-, one plug-, and one bottoming-chamfer tap.

Multiple tap sizes allow tapping a range of hole diameters. Connect these taps directly to drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

All taps and drill bits have a hex shank for direct connection to tools such as drills and power screwdrivers.

Drill and tap holes in a range of diameters. With a drill bit point to drive into the workpiece, these tools can drill and tap holes in a single step. Connect them directly to drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included.

Switch from internal to external threading with interchangeable tap and die adapters. Use them with the included ratcheting wrench.

Clamp these dies around your workpiece, so you can start thread repair anywhere along the length of a bolt, stud, or rod.

Cut several sizes of external screw threads.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

Install these inserts into plastic parts to create a secure base for fasteners.

Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.

These assortments include various sizes of thread-locking inserts.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

Forming the strongest hold of any of our threaded inserts, these inserts have a distorted internal thread to lock screws into place and keys that drive into surrounding material to prevent slipping and rotating.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.

A distorted thread grips the screw to resist loosening.

Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A dry film keeps the screw from sticking or binding in these inserts during installation.

A dry film keeps the screw from sticking or binding in these inserts during installation.

A distorted thread grips the screw to resist loosening.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.