Filter by
Material
DFARS Specialty Metals
Export Control Classification Number (ECCN)
Thickness
For Joining
Height
Toilet Mounting Flanges
 |  |
Style A | Style B |
 |  |
Style C | Style D |
 | |
Style E |
Repair or replace the connection between your toilet and drainage system.
Style A—Install Style A directly on top of a damaged or rusted rusted flange—no need to remove the original. Screw them directly to the floor.
Style B—Install Style B directly on top of a damaged or rusted rusted flange—no need to remove the original. Screw them directly to the floor. Style B flanges don't extend past the existing flange, so they're best for repairing flanges set below the finished floor.
Style C—Style C include everything you need to repair a broken flange. Use the washers to position the repair bar under the broken piece, then secure it in place.
Style E—Style E allow you to offset the flange face up to 3/4" from the base in any direction, so you can reposition a toilet without modifying your drain. The base has a rubber gasket to seal your pipe.
Adjustment Bolts—Flanges with adjustment bolts can be installed up to 3" above the top of your pipe, so you can match the height of finished floors. When you tighten the bolts, a compression joint expands to press against the walls of the pipe, holding it in place.
Mounting | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Style | Material | For Drain Pipe Size | Thk. | Fasteners Included | No. of Holes | Hole Dia. | No. of Slots | Slot Lg. | Slot Wd. | Includes | Each | ||
| A | Steel | 5 | 1/8" | No | 6 | 5/16" | 2 | 2 1/2" | 5/16" | — | 00000000 | 00000 | |
| B | Stainless Steel | 3, 4 | 1/4" | No | 6 | 1/4" | 2 | 1 5/8" | 1/2" | — | 000000000 | 0000 | |
| C | Stainless Steel | 3, 4 | 1/8" | Yes | 2 | 3/8" | 1 | 2" | 1/2" | One Repair Bar, One Connector, Four Washers, Two Anchors, Two Screws | 000000000 | 0000 | |
| D | White PVC | 4 | 7/16" | No | 4 | 1/4" | 2 | 1 1/4" | 11/32" | Adjustment Bolts | 00000000 | 00000 | |
| D | Black ABS | 3 | 3/8" | No | 8 | 1/4" | 4 | 2" | 1/2" | — | 000000000 | 00000 | |
| D | Black ABS | 4 | 7/16" | No | 4 | 1/4" | 2 | 1 1/4" | 11/32" | Adjustment Bolts | 00000000 | 00000 | |
| D | White ABS | 3 | 3/8" | No | 8 | 1/4" | 4 | 2" | 1/2" | — | 000000000 | 00000 | |
| E | White ABS | 4 | 3/8" | No | 6 | 1/4" | 2 | 2" | 1/2" | — | 000000000 | 00000 | |
Bowl-to-Floor Toilet Mounting Hardware
 |
Plastic |
 |
Brass and Stainless Steel |
Fasten toilet bowls to the floor.
3 1/2" Long—3 1/2 lg. bolts are often used when the toilet flange is below the finished floor.
Material | Thread Size | Lg. | Includes | Each | ||
|---|---|---|---|---|---|---|
| Brass | 1/4"-20 | 2 1/4" | Two Bolts, Two Nuts, Two Washers | 0000000 | 00000 | |
| Brass | 1/4"-20 | 3 1/2" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Brass | 5/16"-18 | 1 3/4" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Brass | 5/16"-18 | 2 1/4" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Brass | 5/16"-18 | 3 1/2" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Plastic | 5/16"-18 | 2 1/2" | Two Bolts, Two Nuts | 000000 | 0000 | |
| Stainless Steel | 1/4"-20 | 2 1/4" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Stainless Steel | 1/4"-20 | 3 1/2" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Stainless Steel | 5/16"-18 | 2 1/4" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 | |
| Stainless Steel | 5/16"-18 | 3 1/2" | Two Bolts, Two Nuts, Two Washers | 0000000 | 0000 |
Tank-to-Bowl Toilet Mounting Hardware
 |
Connect toilet tanks to toilet bowls.
Material | Thread Size | Lg. | Includes | Each | ||
|---|---|---|---|---|---|---|
| Brass | 5/16"-18 | 3" | Two Bolts, Two Hex Nuts, Two Wing Nuts, Four Rubber Washers, Four Steel Washers | 000000 | 000000 |
Toilet Mounting Flange Spacers
 |
Use these spacers to raise your toilet flange when it sits below the finished floor. They’re often used when laying new flooring.
PVC—PVC spacers adhere to an existing toilet flange with PVC primer and cement, also known as solvent weld, or with silicone sealant. Stack multiple spacers to raise the flange height so it is flush with or above the finished floor.
Toilet Mounting Flange Spacer Kits
 |
Use these spacers to raise your toilet flange when it sits below the finished floor. They’re often used when laying new flooring.
Polypropylene—Polypropylene spacer kits include the components required to lift the flange up to 1 5/8". They are easier to install than individual spacers because they do not require silicone sealant. They include a toilet mounting flange that sits on top of the existing flange for a level mounting surface.
Mounting | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Material | For Drain Pipe Size | Thk. Range | Fasteners Included | No. of Holes | Hole Dia. | No. of Slots | Slot Lg. | Slot Wd. | Includes | Each | ||
| Polypropylene | 3, 4 | 1/8" to 1 5/8" | Yes | 6 | 3/16" | 2 | 1 7/8" | 5/16" | Four Spacers (1/8", 1/4", 1/2" 3/4" Thick); Gasket; Toilet Mounting Flange | 0000000 | 000000 | |
Toilet Seat Fasteners
 |
Secure toilet seat hinges to your toilet bowl. Made of plastic, these fasteners won’t scratch or damage your toilet. They’re compatible with most top-mount toilet seats.
Material | Thread Size | Lg. | Includes | Pkg. Qty. | Pkg. | ||
|---|---|---|---|---|---|---|---|
| Plastic | 3/8"-16 | 2 1/2" | Two Bolts, Two Nuts | 2 | 000000000 | 00000 |
Urinal Flanges
 |
Connect a urinal to your drainage system. These mounting flanges come with a gasket and mounting fasteners, so they’re ready to install. If you’re attaching them to your existing drain, choose the same material.
ABS—ABS is more impact resistant than PVC.
Toilet Supports
Increase the weight capacity of your wall-mounted toilet with these steel supports.
Floor Mount
 |  |
Floor-mount supports rotate at their base to adjust to the height of the toilet. They have an ABS cover that prevents corrosion and resists impacts from bumps and kicks. Attach these supports to a toilet bowl with the included caulk. An aluminum ring mounts to the floor with epoxy (not included) to hold them securely in place. You can raise and lower the base to clean underneath the toilet.
Ht. Range | Rod Material | Cover Material | Wt. Cap., lb. | Includes | Each | ||
|---|---|---|---|---|---|---|---|
| 7 1/2" to 14" | Zinc-Plated Steel | ABS | 1,000 | Aluminum Ring, Caulk | 0000000 | 0000000 |
Wall Mount
 |  |
Wall-mount supports have mounting holes to fit over the existing bolts on the toilet. Adjust them to the height of your toilet using one of the three extensions. The powder coating on these supports prevents rust and won’t degrade when cleaned with soap and water. They have a spring-loaded leg that swings out of your way so you can clean the floor beneath the toilet.
Ht. Range | Material | Wt. Cap., lb. | Includes | Each | ||
|---|---|---|---|---|---|---|
| 5" to 14" | Powder-Coated Steel | 1,000 | Mounting Hardware | 0000000 | 0000000 |
