Use this PTFE sleeving in applications where temperatures reach up to 500° F.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

With excellent torsional strength, this sleeving withstands the extreme twisting found in robotics. It has impact strength similar to steel yet is lighter than most other sleeving materials. Stretch it to fit over items for easy installation; it tightens around its contents for a secure fit.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Made of PPS plastic, this sleeving shields cable, hose, and pipe from oil, acids, and other chemicals. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

This sleeving withstands temperatures over 1000°F, such as in refineries.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Coated in acrylic, this sleeving holds up to rapid temperature changes, and it won’t break down from refrigerants, solvents, oil, or lubricants. Also known as hermetic sleeving, it’s designed to protect wires and hose inside air-tight motors, such as those used in air conditioners.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

With a flat, oval shape, this sleeving fits better in confined spaces than standard corrugated sleeving.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Often used in robotics and other automated applications, this sleeving adds an extra layer of protection and insulation to cable and hose carriers.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Sheathe cable, wire, and hose in a protective cover in case of a fire. Rated VW-1, this sleeving meets requirements for preventing the spread of flames based on a timed test with vertically suspended material.

To stop rodents from chewing on this sleeving and damaging your wire, cable, or hose, it’s reinforced with glass fibers that irritate rodents’ gums. Wrap it around components without having to disconnect them.

Wrap this sleeving around cable, cords and wires to protect them and to form bundles.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Identify wear and tear on your sleeving before its contents become exposed. This sleeving has a yellow inner layer that shows through when the black outer layer wears off.

Protect cables, cords, and wire and form them into bundles in your food-processing plant while lowering the risk of contaminating the food.

Made of neoprene rubber, this sleeving has excellent abrasion resistance. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

A mica and silicone rubber blend allows this sleeving to withstand intermittent heat up to 2100° F. It can be quickly applied to hose or cable like tape, so it’s a good option for emergency patches.

Seal the end of crimped connections, such as motor coils, to insulate and protect them from moisture and abrasion.

The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.

For better protection against abrasion, tears, and punctures, this tubing has thicker walls than standard tubing.

Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.

With excellent durability and chemical resistance, this tubing withstands demanding use.

Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.

Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Create a tight, water-resistant seal over irregularly shaped components. When heated, this tubing shrinks down to about 1/6th of its original ID, while an adhesive lining melts and forms a barrier around your component.

Protect light bulbs, capacitors, and other electronics—this FEP tubing adds a tear- and cut-resistant layer that even contains shattered glass if the bulb breaks.

Even with walls as thin as tracing paper, this PET plastic tubing withstands tears and nicks. Thanks to its thin walls, it shrinks down in seconds instead of minutes and at lower temperatures than PVDF and FEP plastic tubing.

Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.

With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

Resistant to diesel fuel, gasoline, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

Keep general purpose tubing in a variety of sizes on hand.

A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.

Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this tubing has an adhesive lining that melts when heated to bond it to the underlying surface.

Use this wrap with heat-shrink tubing to create a moisture-resistant seal. Apply it like tape around wire and cable, then slide the tubing over the wrap. The wrap melts when tubing is heated and bonds to the underlying surface.

Permanently seal pipe, tubing, conduit, and even crimped electrical connections. Slide these flexible caps on and use a heat gun to tightly shrink them to the shape of whatever they are covering. Their outer surface shrinks while the inner wall flows into voids to create a sealed connection.

Protect the cables on your MIG guns from weld spatter.

These rigid, lightweight melamine foam tubes are wrapped in an ISO Class 5 and Fed. Spec. Class 100 clean room jacket that is suitable for sanitary and washdown applications. They’re typically used on cold and hot water piping and with refrigeration systems.

These insulation tubes and sheets meet ASTM E84 standards for flame and smoke.

Very rigid with a 0% water absorption rate, this insulation is unaffected by corrosive environments, organic solvents, and most acids. It is typically used in chemical-processing systems and underground lines.

Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines.