Because they require a key to operate, you can limit who is able to adjust these valves. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 exhaust center valves.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create two actions, such as extending and then retracting a double-acting cylinder.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Also known as 4/3 exhaust-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Control six different outputs from a single source of airflow. These valves have one inlet port and six outlet ports. Push in and rotate the dial to move between outlet ports and send airflow to a different output.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

Because they require a key to operate, you can limit who is able to adjust these valves. They create one action, such as extending a cylinder.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way and 5/2 valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Use a single valve to create motion and control the speed of that motion.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

These valves create one action, such as extending a cylinder. Also known as 3/2 or pilot valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They activate when an object, such as a box rolling on a conveyor, pushes the actuator. Also known as 4-way and 5/2 valves.

Also known as 4-way and 4/2 valves, these valves create two actions, such as extending and then retracting a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.

Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

A fine-adjustment dial allows tighter control of airflow and cylinder speed than other flow control valves. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

A numeric indicator provides a relative measure of airflow, similar to the volume dial on a speaker, so it's easy to set the same flow rate with each use. Mount them directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. They control the speed of air-powered equipment by adjusting the volume of airflow.

Designed to be mounted inline, these valves can be placed in easy-to-reach locations. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

These valves handle pressure up to 265 psi. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Made of PBT, these plastic valves are more corrosion resistant than valves made of aluminum or nylon. A single dial adjusts airflow equally in both directions, controlling the extension and retraction speed of an air cylinder at the same time.

Protect air-powered equipment in emergency shut-off situations—when system pressure drops, these valves automatically close to stop cylinder motion, even at mid-stroke. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

A padlock locks the handle of these valves in the shut-off position so you can disconnect air tools safely.

Slide the knurled sleeve in one direction to stop flow, and slide it back to start flow again.

Also known as blocking valves, these valves allow airflow while an air signal is applied to the air pilot. When the signal stops, the valve closes, trapping air in the system.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.

Also known as air fuses, these valves close automatically to turn airflow off when air volume exceeds the shut-off flow rate.

Control the flow of exhaust air while also regulating the exhaust air speed. These valves dump exhaust air to the atmosphere without routing it back through a directional control valve. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.

A muffler reduces exhaust noise. Valves allow airflow into your equipment and then quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. Also known as quick exhaust valves.

Choose the pressure range you need. When these valves receive an air signal, they quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. They're often used with air compressors that require continuous operation. Also known as quick exhaust valves.

Convert a continuous stream of air into a series of quick pulses, reducing air consumption by up to 50% and improving performance in air-blowing applications such as cleaning and drying.

Prevent air from escaping an air storage tank when the air compressor is not running. These valves open to allow flow into the tank and close when flow stops or reverses direction.