Brighten chemical plants, refineries, and other facilities where flammable and combustible gases, dust, or fibers may be present in the event of a leak or ventilation failure. These lights are rated for use in NEC Class I, II, and III, Division 2 hazardous locations.

The enclosure on these jelly jar lights contains explosions, sparks, and flashes. These lights are safe to use in NEC Class I, II, and III, Division 1 hazardous locations.

Built for hot, hazardous areas such as steel mills and refineries, these lights work in temperatures up to 212° F. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Safely light up chemical processing plants, mining operations, and other large areas where combustible gases and dust are present. These lights have an explosion-proof housing that contains sparks and flames, so they won’t react to nearby hazards.

IP or NEMA rated, these lights have a sealed lens to keep dust and moisture out for protection against washdowns. All meet ETL or UL standards for wet locations.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

No need for wiring—these lights plug into a standard wall outlet. Also known as shop lights.

Brighten high-traffic areas with our most rugged ceiling lights. Rated IK10, the highest impact resistance rating, they’re protected by a 16-gauge cold-rolled steel frame and polycarbonate lens.

A wraparound lens disperses light from the sides as well as the bottom to produce ambient lighting.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Illuminate steps to reduce the risk of tripping or falling, especially at night or in poorly lit areas.

Brighten large, open areas, such as warehouses and manufacturing spaces. IP rated and UL listed for wet locations, these lights are sealed against washdowns.

Also known as jelly jar lights, these lights are sealed to keep out humidity and dripping, splashing, and falling liquids. All are UL listed for wet locations.

Also known as sconces, these lights are a stylish choice for ambient and accent lighting in hallways and entryways. They’re UL or ETL listed for wet locations, so you can install them outdoors—rain and humidity won’t be a problem.

Brighten your ISO Class 3 clean room with long rows of lights—you can wire these lights together at the ends. They have an airtight seal that keeps contaminants from entering your space.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

Illuminate machines and monitor processes where flammable and combustible gases, dust, or fibers are present—from paint spray booths to chemical plants. These lights have an enclosure that contains sparks, flashes, and explosions.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Brighten loading docks and trailers—these lights swing out from the wall and tilt to direct light where it’s needed.

A sealed head and switch keeps these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.

Expand the reach of emergency backup lights. These add-on heads are often used to extend emergency lighting into stairwells, exits, and other remote areas.

A gasket seals the enclosure of these backup lights from washdowns.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

Safely light up large spaces where combustible gases and dust are normally present. Rated NEC Class I and II, these lights have a housing that contains any sparks or flames and seals out ignitable gases, vapors, and dust.

Flood hazardous areas with light—these lights are intrinsically safe, meaning they can’t cause an explosion or fire. Rated NEC Class I, II, III, and Zone 0, they’re safe to use in areas with ignitable concentrations of flammable or combustible gases, dust, and fibers.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, Class II, and Zone 1.

Hang a string of lights overhead to brighten wet jobsites. IP rated, these lights are sealed to keep out dust and moisture from washdowns, splashes, and sprays, even outdoors.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

From pipes to pallet racks to control panels—these lights clamp onto almost anything and swivel to direct light just where you need it.

Our brightest plug-in floodlights, these lights illuminate large worksites—about the size of a hockey rink.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Brighten remote areas using the same battery as your other cordless Milwaukee tools.

With a rounded, weighted base, these floodlights wobble—but don't fall over—when bumped.

Bring light to remote, wet areas. These floodlights are IP rated to handle humidity and dripping, splashing, and falling liquids. Adjust their tripod up and down to direct light as far as you need.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

Guide pedestrians and drivers at night with lighting that defines paths and driveways. These lights produce ambient illumination without the glare of overhead lights.

No need for wiring—these lights plug-in with a three-prong plug.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Hardwire these lights to a power source.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Light up drawers and enclosures where power isn’t available—these lights are compact and powered by battery.

Gooseneck arms can be repositioned faster and more easily than articulating arms.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.